I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hello,
How to use the nordic android ble library, I have implemented it but only once when on the road can receive data. From the BLE device every minute sends data.
I...
Heyy I working on project where i am planing using XIAO nrf52840 chip am using Ardunio IDE for Rapid development, I was unable to implement wake and sleep functionalities...
On calling `bt_enable`, I find that the program hangs - the function fails to complete.
Enabling logging, it looks like HCI command buffers aren't being properly released...
Hello team,
I successfully migrate from the SDK 2.6.1 to 2.9.0.
Now, I am trying to build the modem_shell sample for the nrf9160DK with nrf9160dk_nrf9160_ns .overlay file...
Hi, I'm using ezurio BL653µ and want to create a custom board in ncs2.8.0 (HWMv2) but i cannot sellect the nRF52833-CJAA variant. What do i do? Do i select another variant...
We are considering to implement ”ASCS/BAP/CAP/CSIP/PACS” as the BLE profile.
Do you have any QDID for this profile certified in SDK 2.3.0? If yes, please provide each of...
Hello,
I am completely new to Nordic eco system. What I basically want to do is make a simple bluetooth mouse using a module and the Connect SDK with the HID sample.
Now...
Hi team,
Linking error for ble_uart
Segger embedded studio - 8.22a.
SDK version - 15.0.0
error -
Building 'ble_app_uart_pca10056_s140' from solution 'ble_app_uart_pca10056_s140...
nRF52832 is used as Central to get data from nRF52820 (Peripheral).
There is no problem when you always communicate, but if you can not communicate due to running out of...
I have a project using ncs 2.7 with the nrf9160. My west manifest file is set up to import all and it takes forever, so I am trying to narrow it down to only what is needed...
Hello, Currently i am working on ble mesh and specifically on different nodes implementation, Proxy node, LPN node, Friend node. But when i am starting to implement and testing...
Hello,
i am using the Wi-Fi: Scan sample with the nRF 7002 Deveolpment Kit.
I am trying to alter the clock frequency/QPSI mode (Dual/Quad) of the QSPI Bus connecting the...
Hi. I am using nrf52832 and 17.0.2 sdk.
What I want to do is to provide automatic connection between my nrf device and my android device. For this purpose, I use the HID...
I'm trying to use AAR peripheral, but I don't know the structure of output DMA job list, as it's not defined in the datasheet. I was trying to use one job pointing to flat...
Hi,
I'm transmitting using the nRF24L01P and using the nRF52810 as the receiver, 5 byte address.
We send a 2 byte packet usually 0x00, 0x00 until data is ready. If I set...
