I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I want to use the ADC for a burst @ 8khz.
I use this sample " test_adc_sample_with_interval " from https://github.com/zephyrproject-rtos/zephyr/blob/master/tests...
Greetings...
Please help me understand why PB-GATT support is removed from SDK UART coexistence example?
The dilemma I am facing is as follows:
1. No PB-GATT for SDK...
Hello, Currently, we trying to use PPI with the SPI module (we use the SDK 15.3.0) We expected that the SPI makes one read transaction every 5 us ; to do this, we use 2 PPI...
Hi there,
My project needs TrustZone and ETB feature. The manual clearly states that the board supports TrustZone and ETM. I wonder if it also supports ETB to store trace...
Hi,
I am using SDK15.3 with the SoftDevice enabled. I've been unable to get any SoC events after making a call to sd_flash_page_erase. I registered my observer as follows...
I'm trying to develop a Bluetooth application where my Nordic nrf52 DK sends an event when I push the button and another when I release it.
I'm trying to apply this on the...
Folks,
One of the devs here found that all warnings were switched off in SES, so I've recompiled and got rid of most of the 1400 odd (sic) warnings by suppressing unused...
Hi
I want to use loggers in the program. I understand that the code itself uses NRF_LOG. But I do not understand where those log details are printed. So, how do I create...
I am experiencing an immediate BLE disconnect when trying to use DLE. I can write up to 20 bytes of data, but if I try to write more 21 bytes or more I get an immediate BLE...
I was wondering what I have to do to clear all stored mesh data on flash.
Do I have to initialize the whole mesh, or can I init only a subset?
What do I have to do so...
Hi all, I am working with NRF52840 and Open Thread SDK V3.1. Everything is normal.
But now, I want to run open thread example in SDK with NRF52811. T o reduce product costs...
Dear every one
I have a project with nRF52832 dev kit. I want it sleep (mode on) and wake up every 2 minute. When it wake up, it broadcast BLE and if it sleep it not broadcast...
I have a custom PCB that I designed for use with the nRF52811. I have tried to connect to it using the nRF Connect Programmer to program a Soft Device but I am unable to connect...
dear folks,
I bougth my dev kit last week from digikey. I tried the asset tacker demo out of the box without success. I tried nearly everything. Updated the modem to v1...
