I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi,
I am running the Asset Tracker application from a fresh clone of the 0.4.0 nRF connect SDK. Using the supplied iBasis SIM.
It connects after booting, and I can monitor...
Hi,
Iam using nRF52840 , And got ANT sdk from thisisant.com. Placed in the required folder & Using ANTware II v4.1. All things going well, But after programming the DK nRF52840...
Hey Nordic Community ,
I have been trying to get the Modem firmware up and running without success for a few days now (Attempted with 2 different PCs and 2 DK with same...
hi....
i am using nrf52382 .. segger 15.2version
here i have attached two programs ble_uart and twi sensor ... its working fine but data is received over ble_uart app...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use CURVE25519.
I made my code refering to example "ble_app_multirole_lesc" and "nrf_crypto_keys.h".
NRF_CRYPTO_ECC_PRIVATE_KEY_CREATE...
Hi all,
When i walk-through the battery-service provided by nRF SDK, i note the presence of " Report Reference Descriptor " in the characteristic addition function.
I...
Hello,
I am trying to insert fds functionality to light switch client. I added all files and libraries to project. But when i try to compile project i face with errors...
When I am initializing BSD-library with bsd_init(), the function gives me back an value which i can´t find anywhere 0x00008108.
Hopefully you guys could tell me what this...
Are the virtual page sizes only allowed to be 1024 and 2048 for the nRF52840?
// This is a multiple of the physical page size. Is this allowed or not?
// <i> Expressed...
I am attempting to do the assert_tracker example. I have gotten all the code to build through Segger and upload to the DK. The problem is when I'm watching the terminal for...
Hello there,
I want to run Radio Test on one nR52832 based custom board.
I have flashed the example from SDK 15.3 on the custom board using PCA10040.
I have done the...
I am trying to use nRF9160 as ble gateway for uploading data from two nRF52832. I am wondering is it possible? can I connect nRF9160 (one gatt client) to two nRF52832 (two...
Hello,
I have the following problem. I want to create a whitelist using the PM on a manually added peer.
I manually add a peer by adding its GAP address.
Then I try...
Hello!
Like several others on here, I’m trying to make a multilink nus central firmware. My Peripheral devices run the ble_app_uart example, and the central device runs...
