I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to set up the sniffer on nRF52832 DK PCA10040. I am not seeing the COM port on the Wireshark interface. I can see it on the device manager. I have looked at other...
Hi Everyone , I am using SDK v15.0 for nrf52840 with segger embedded studio.
I tried the example code given for blink freertos. I am able to run two tasks but as soon as...
Hello,
I am using nRF52832 and having a problem with the Low Power Mode. I am not sure if I am either not getting it to stay in low power mode when my UART is initialized...
What is the maximum server node count running light switch example? In documentation there are multiple facts: 1) " If you have more than thirty boards for the server, set...
When I use the nRF Toolbox to upgrade the nrf52832 device on the mobile phone (huawei mate9 Android8.0), I have the following questions: The first time I opened the update...
The device sending data will be accepted to the callback function nrf_gzll_device_tx_failed， But the host side receives the data and calls the function nrf_gzll_host_rx_data_ready...
Hi!
I'd like some help in understanding the initiation of provisioning. We would like to have something along the lines of:
Using a mobile app, a user receives a list...
Because I encountered the same problem, so I needed help. I ran the nordic official example E:\sdk\nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_multilink_central...
I have successfully used the guide for BLE DFU.
But now I have trouble using the DFU via serial port. Do you have a guide for serial DFU?
I have tried two things.
...
I have a weird question:
On the nRF DKs (51&52) there are pin headers to connect them to an Arduino.
When delivered, on these headers there are some sort of plastic clamps...
As I working on a new project I am writing the code to support the new SDK driver structure and not including any "legacy" code support.
This highlights the fact that the...
I have a custom board with nrf51422-QFAC, used with SD 130 and SDK 12.3.0. My firmware consist of ble_app_hids_keyboard example modified. Schematics are attached below.
...
Hi all,
I using 1 Provisioner provisioning for some Nodes (light switch server) . If I have 5 Nodes in mesh network
I want to remove Node 4 from network and then add it...
