Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
here is 2 question for this example. (v2.9.0) as i looking for this example, there are some limitations like belows.
One BIG, one of the two BIS streams (selectable...
Hi
I remember the Devzonw could ask for hardware instructions. My matching circuir has used the nRF54L15 reference design and nRF21540 DK design, all the value is the same...
I am developing a proof of concept project using Wave share BLE400 module and the final product of this project should work on button battery backup for years. so essentially...
Hi, I recently upgraded our ncs SDK version from 2.6.0 to 2.9.0 for a custom matter application development using an nRF5340. We also support a smaller debug app that is BLE...
When setting the following channel sounding parameters with bt_le_cs_set_procedure_parameters I am getting E: Failed to set procedure parameters (err -22) or BT_HCI_ERR_INVALID_PARAM...
Dear,
i think that the evb nrf52 dk missed the bootloader because when i push on Segger (target connect j-link), there is the message NO PROBES CONNECTED VIA USB.
I...
Hi,
We are currently in the process of evaluating the nPM1300 PMIC for our project and I would like to know if there is a way to supply Vsys using the battery even when...
Hi, I'm in India Using JIO 4G sim card in India can't connects to NB-iot . Here network provider supports NB-iot but if i try to connect the network it is searching for a...
Hello,
I have always been able to use VSCode to find various installed toolchain versions, but today I suddenly cannot find toolchains other than v2.2.0.
I checked and...
Hi
I have a beacon sending out some data, and I have already finish the TX side, I also want to have a RX side to receive the data, in addition, as there are many other...
GNSS not working on Thingy:91 after modem_shell flash — help and gnss start return ERROR
Device:
Thingy:91 (NK-THINGY91) RS Stock No. 196-3901 nRF9160 + nRF52840 combo...
Hi Nordic,
I’m new to the nRF Connect SDK for VS Code and currently evaluating the nRF7002 DK board. I’ve been able to build and debug firmware successfully for the NRF7002DK_NRF5340_CPUAPP...
If you see i'm trying to install toolchain and nrf sdk v2.6.1 via vscode, the installations seems to be successful but at the end of toolchain as well as sdk installation...
Hi, In my project we are using the ESB between a nrf52811 and a NRF5340dk and are trying to evaluate the maximum speed we can reach with ESB packet transmission without acknowledge...
Hi Nordic team:
I am configuring a low power application for the nrf52833 board (custom board). This is a very low power application and I want the board to stay on sleep...
