Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
1. ZigBee Cluster Library Specification(Rev 6) -> 3.3.2.2.3 Battery Information Attribute Set -> Table 3-18. Attributes of the Battery Information Attribute Set tell...
Hi,
I am a beginner to nrf9160.
I already can do send the large data to server. (Maybe not too large just about 15KB)
In my test, I will send that data in every 25 minutes...
Hi,
I am not able generate dfu_package.zip using nrfutil.
I am using ubuntu 18.04, and python2.7 is installed is default python version.
I get the following error when...
Hi!
I have bought the Thingy:91 and in user guide (on page 12) it says that the nRF91 DK should be used to update the modem firmware, further more, it seems like it is only...
Hi I am trying to program the bsp buttons on the NRF52 DK, so pushing button 1 will toggle start advertising and going to sleep by calling sd_app_evt_wait().
I have successfully...
Hi All
I'm trying to use the Adc in Sample convert mode: "nrfx_saadc_sample_convert(0,&ADC_Val);" to sequential read two ADC pins .
I have used the code below to init...
I want to add a node(server) in multiple group in Mesh.
Application is if any switch pressed next two corresponding light to be trigger to on. for that one server subscribe...
Hi,
We are using Mesh successfully with the Mesh SDK 3.1.0 combined with Nordic SDK 15.2 and Softdevice 6.1.1.
Due to the nature of our BT device I would like to explore...
Hi,
I am new to the nordic platform .I am using. BL652 modules .I was able to blink my on borad LED and then made the device as peripheral to advertise with the device name...
I'm using the nRF52832 with softdevice s132 and SDK14 with ARM GCC
I'm trying to set up the SAADC peripheral to read battery voltage, and I can get everything working as...
Hi all, We use a kind of widely used nrf24l01 module in our product developement.It use the nodic's reference design of nrf24l01 with an external pa/lna.TXEN and RXEN of the...
Hello! I have an Android phone and nRF52840 as a peripheral. Now I want the peripheral to have a whitelist with exactly 1 peer with whitelist being dropped at button press...
I read in many blogs that I can use access layer directly without models to communicate .
So access layer is under mesh?
means that can i send data to remote node(out...
