Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi,I made a 52840 board ,it's p0.18 hanging, without connecting a 10k pull-up resistor and a 100nf capacitor to ground. I connected 3v3, GND, SWDIO, and SWDCLK from the 52DK...
NRF54L15 NCS 3.02
I have to change my BLE advertising from Legacy to Extended. Looking at the Zephyr example "advertiser" which compiles & runs fine, but I notice that behaviour...
Hi,
I am currently trying to connect a nrf52811 as an companion to an ESP32 user UART.
I am using the interrupt driven UART implementation as kind of the last resort....
How can I set a custom interval for *extended* advertising?
I'm currently calling bt_le_ext_adv_start ( struct bt_le_ext_adv * adv , const struct bt_le_ext_adv_start_param...
~~~~~~~~~~Environment ~~~~~~~~~~ nrf54L15 + NCS 3.1.1 + VSCode + Win11 ~~~~~~~Reproduction Steps~~~~~~~~~ 1. without pm_statics.yml, with following configs (see attachment...
Dear Team,
I am experiencing a weird issue with the firmware on my custom EV board with NRF54L15.
My firmware is using MCUBoot and partition manager (I use a separate...
Dear Team,
I need to switch LXFO to internal RC for MCUBoot, however, I am experiencing troubles configuring it on NCS 3.0.1 (NRF54L15).
If I just add my RC settings to...
Hi,
Our project requires an unusual combination of running BLE, Gazell, and raw radio packets for time sync simultaneously.
Time sync and BLE are infrequent activities...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I've run into an issue when doing some compatibility testing between our client's legacy device (802.15.4 transmitter) and the current device in development (802.15...
In the introduction to the bare metal SDK option for the nrf54L:
https://www.youtube.com/watch?app=desktop&v=31znTI-hnCQ
it mentions at around 58:00 that single bank...
I am using nrf connect SDK toolchain version 3.1.1 and nrf connect sdk version 3.1.1 , By default I don't have zigbee related samples/examples and also zboss stack library...
The original question was: "The nRF52840 PS mentions, that this chip contains an ETM but it does not mention the implemented version."
Researching the topic more, I found...
Hello Team,
We have noticed a very weird issue with the nRF5340 Audio DK. After flashing the audio application code given by nordic, everything works perfectly fine. No...
