I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi everyone,
We design an application using the nRF52840 and SDK16. This application is intended to be used for gait analysis and one of the requirements is a real-time...
Hello,
I'm trying to initialize the values of all my attributes using sd_ble_gatts_value_set . According to the documentation, the connection handle is ignored if the value...
Hi,
I unsecured my device and running it with JLink RTT to observe logging. If I program uicr registers during this process, the devices gets secured and I have to redo...
Hi,
I'm BLE-sending out Sensor values using a nrf52832. When the sensor gets a (new) value an interrupt is generated and the nrf then transfers the value in the gpiote inerrupt...
Hi. I have read the documentation and I have a couple of questions:
What makes work different mesh_gatt and nrf_ble_gatt? Why can't they work together (maybe it's because...
hi professor,
I add the CONFIG_NO_OPTIMIZATIONS=y but ble connection timeout In my pheripheral project .When I delete CONFIG_NO_OPTIMIZATIONS=y, the ble will connection...
Dear Nordic Team and Community!
I have again a question concerning advertising. Currently I am working with the devices nRF52840Dongle (Advertising, S140, 10059) and nRF52840DK...
Hi, I'm using nRF52805. My "1 button to turn ON/OFF system" code works perfectly fine on nRF52 DK.
However, when I migrate the code to nRF52805, Segger shows me an error...
Before exploring the Zephyr ecosystem, I plan to study in detail the periphery of my microcontroller (nRF5340).
For this purpose, I plan to try examples from nRF5_SDK_17...
Hi we are designing custom Board using nrf52840 and want to use NFC as mode of communication. We want to use NFC in nrf52840 in 2 way communication mode. My questions are...
I just figured it out it is not I2C protocol. I need to write all the command by Bit-Bang mode.
How can I send/receive data with manual bit command to SHT1x sensor?
Can...
Hello,
I am trying to setup a windows docker image to use on a build server for zephyr nrfsdk projects, but i am haveing difficulty getting things configured correctly...
It was suggested in other cases that it may be more power efficient to use uart without easydma in some cases.
I am using NCS and I see CONFIG_UART_0_NRF_UARTE is defined...
Hi,
I am using Thingy91 and I successfully connected it to the cloud, also able to pull all sensor readings with the curl command: curl https://api.nrfcloud.com/v1/messages...
Hello!
I am starting to profile our device using the PPK2 and I am seeing some strange measurements when the device goes into its low power mode.
I'm attaching an image...
