I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
I am working on creating a Bluetooth Mesh network using the BGM220P as a sensor node. My goal is to send sensor data (e.g., temperature) from the BGM220P and have it received...
Hi
I am having some issues flashing the modem firmware to a custom board using the nrf9151 SiP.
I can, with no issues, flash programs to the chip, but when i want to...
Hi.
I'm playing with an scenario based on two nrf52840dk and a dongle.
I have deployed a OTBR on a Linux Ubuntu22.04 and flashed the dk with OT COAP Server and Client...
After a lot of help, I've managed to get a central_uart with custom UUIDs going. After stripping out as much unwanted code and callback functions as possible, moving UART...
Hi,
I am new in Device tree concept. I am trying to operate a buzzer via PWM.
In our board, the buzzer is connected in GPIO 3.
I changed a segment in file nrf52dk_nrf52832...
Hello,
At the moment I have a correctly working Azure IOT hub connection.
DPS works, device twin configurations works and transmitting data to the hub is also no problem...
Hi All I started on the fundamental course in the academy. I did everything by the letter in lesson 1 / exercise 1 Yet when I plugged in my 52840 devkit I could no load the...
Hello,
I am working on a project involving the nRF54L15dk and need to connect a peripheral's reset pin to the reset functionality of the DK. However, I noticed that the...
This is heavily processed code just to show what I'm doing with discovery: I can see that first time I call for discovery I get BT_GATT_DISCOVER_PRIMARY cnt_3 = 3. Then I...
I discovered this chipset and have found a dev board on eBay for $37. Is it worth it to tinker with? I have the 2.8 version of the toolchain. And Sdk. On vs code.
I have...
Why are RADIO_MODE_MODE_Ble_LR125Kbit ， RADIO_MODE_MODE_Ble_LR500Kbit and RADIO_MODE_MODE_Ieee802154_250Kbit not supported in the ESB routines? If I want to use these configurations...
Hi,
I'm working on a project where I want two units to be able to wirelessly send packets to each other whenever they need to. Sometimes only one of the two units may be...
If I initialize the IPC and then turn on the bt_enable, it will lead to the status quo in Figure 2, what is the reason?
If I block k_sem_take (&bound_sem, K_FOREVER) and...
