Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
[ Just figured out it doesn't work the way I thought ]
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
This is the command I used to generate setting.hex.The primary address of my app is 0x19000.
This is my hex distribution. The library used is nRF5_SDK_17.1.0_ddde560....
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. We are using a QSPI flash, MX25U51245G ( https://www.macronix.com/Lists/Datasheet...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hi everyone,
I’m designing custom hardware for my application using the nRF54L05 MCU (v2.9.0) . However, I can’t connect to the device from iOS — the connection always fails...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Hello everyone,
I'm working on an NRF54L15 DK evaluation board and I need to use NFCT pins as normal GPIOs. I found out here that I should define CONFIG_NFCT_PINS_AS_GPIOS...
Hi,the Nordic team.
I am using nrf54L15 to develop Matter. I have seen that the official sample programs are all equipped with external flash. How can I run Matter programs...
Hi,
I'm using an ISP2053 (nrf5340) chip on a custom board and debugging using the nrf5340dk. I'd like to use P0.02, P0.03 as part of an SPI bus.
I set up a simple experiment...
