I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi,
I am using NCS 1.5.0 and modem firmware 1.2.3.
In my application I need to receive few commands from PC UART (UART 0).
Baudrate is 115200 without HW control. ...
Hello,
I am currently doing an internship and I am working with the nRF5340 DK.
Until now I have tested the "Thread: CoAP Server" and "Thread: CoAP Client" examples and...
Hi my application is working fine with secure bootloader on devkit PCA10056 using nRF52840 and GCC. Now I want to bring it to my target hardware using nRF52820 to get rid...
Hi,
I am writing my own SPIM driver, when I try to send a 2 bytes message and then a 26 bytes message the second message "crashes" after 2 bytes.
But if I send the 26...
I am looking for information regarding usage of UICR in nRF52840. I want to store Board information like board version number etc.. in UICR probably in the customer registers...
I am using Nordic's NRF_SDK_For_Thread_and_Zigbee_4.1.0.
In that example/thread/ncp, I want to build NCP firmware for uart.
Original uart pins for rx and tx are 8 and...
Hi,
I have nCS installed and when creating a project in nCS installation directory (default path), then i have option to choose "Configure nRF Connect SDK Project" from...
Hello,
For my board i would like to remap uart to pin on GPIO PORT 1.
Current:
&uart0 { status = "okay"; current-speed = <115200>; tx-pin = <20>; rx-pin = <22>; rts...
Hi,
We have a requirement to connect a SPI device to each SPI interface present on nRF52840, and we want to write to those multiple devices in parallel. Is there any API...
Hello everyone,
I would like to run the ANT examples "ant continuous scanning controller" and "ant scan and forward" on my nRF52840DK(PCA10056) boards however it only supports...
Hi,
We have a device based on nrf_52840, SoftDevice_132_3.0.0 and SDK_12.3.0, using BLE for communicating to a PhoneApp and UART for communicating to a washing machine...
I'm writing an application for the nrf5340 with nrfConnect v1.6.1,
I've been able to do the FOTA upgrade through BLE with the example smp_srv located inside zephyr/samples...
I recently got the nRF52840DK and have been able to build/flash a couple simple samples. However when attempting to try the OpenThread CLI example on tool chain v1.6.1 and...
Hi,
cannot run pc-nrfconnect-launcher v3.7.1, built from sources.
```
$node -v
v12.22.5
$git clone https://github.com/NordicSemiconductor/pc-nrfconnect-launcher...
