Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi,
I am following example to connect using TLS. I am not polling, as in the example. Should I expect that after
mqtt_connect, to be called in the callback?
mqtt_connect...
I am encountering an MPSL ASSERT: 106, 501 error followed by a HARD FAULT while running my distance measurement example on an nRF52840 using the nRF Connect SDK v2.5.1. The...
in Bluetooth Low Energy Fundamentals -> lesson 3-> Exercise 2 I opened the solution, I built the config for nrf52840 dev kit. Problem: 2M PHY is not achieved. Update to 2M...
Hi I am a student exploring on the usage of nRF52840 utilsing Thread communication protocol but i cant seems to get it setup for the configuration. The documentation is quite...
Hi,
I've been using the nRF5 SDK (17.1.0) USB Mass storage code for a data logger I have made. I am using a memory chip larger than 16KB and that code has bugs when you...
Hello,
I am currently using the nrf52840 evaluation board in developing a prototype. Once this goes into production, what are my options for programming the firmware? What...
When using l2cap to stream data at a high rate from device to an app we are seeing a hard fault in l2cap_data_pull when there is queued l2cap send data.
When the fault...
Hi,
I encountered a stop scanning issue when running the nrf5340_audio application without any configuration changes .
The only modification I made was changing the log...
I am building a firmware based on nRF Desktop, but can reproduce the issue in nRF Desktop SDK 2.9.0. The issue is that MCUBoot takes almost 1s to start the app, even with...
I'm using the visual studio code extension and things work well. I am now trying to test a more complex project found here but when pressing build I get some very long errors...
I am currently working on a distance measurement library using the nRF52840 DK and nRF52840 dongle. I have successfully obtained distance values on the serial terminal, but...
Evaluating direct access I2C operation with the NRF9160DK. I have a INA219 connected to pin 30 & pin 31. I am aware that there is a zephyr driver for the INA219, but I want...
Hello all,
Going through the nRF Connect SDK Intermediate course with my nRF54L15 DK, I stumbled upon a problem at step 6 of exercise 3 - Interfacing with ADC using nrfx...
NCS 2.6.0, sysbuild with mcuboot
nrf52840
I'm trying to add LED indication during mcuboot image transfer. Currently it takes 20-30 seconds for the image copy and the...
Hello, I cannot use UART1, and I don`t know the reason for that. I run the exercise: https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial...