GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello.
I am developing nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral.
What I want to do is to connect to Central, then bond and then disconnect.
Therefore, sd_ble_gap_disconnect...
Hi
This question is based on the NCS tag v1.8.0.
I am using nRF9160DK SLM application to evaluate the MQTT AT command function.
I got OK if I send a plain text to...
Hi Sir/Miss,
I import cts (current time service) as previous topic which is as link .
I have a compatibility issue in different phone.
The tested conditions are as...
Hi,
I'm thinking of doing a send / receive test of nRF52832. The Bluetooth test set uses MT8852B (anritsu).
At that time, it is necessary to send a signal by HCI or 2...
In the nrfConnect SDK 1.4 there is a sample for chainable RGB LEDs ../ ncs/zephyr/samples/drivers/led_ws2812
I want to use this with nrf9160 so I created nrf9160dk_nrf9160ns...
Hello!
I am able to use the Direct Test Mode application on the nRF52833 development board using the pca10100 DTM firmware found in the 17.0.2 SDK over USB. However, when...
Hello, When I use the recommended X1 and X2 crystals from Epson (Q22FA12800025 and FC-135 32.768KHZ ±20PPM,9.0PF) the device works properly, crystals from ECS did work too...
Hi,
I am doing a design with this component MP06003, but I don`t find this in the distributes in Argentina.
I am looking for this components with others distributes...
Hello Community! I've recently switched from Master Control Panel to NRF Connect. I want to use my NRF51 Dongle (PCA10031) with NRF Connect. Therfore I deleted the existing...
According to eval kit reference BOM list a TDK MLZ1608M100WDT25 10uH coil is the only one on list. Is there any other suggested coil models tested by Nordic? Just wondering...
We are designing a custom antenna for the nrf52833-QIAA. Could you supply the output impedance of the ANT1 antenna pin so that we can run an HFSS simulation on our layout...
Dear Members,
I run 3 devices,
GPS on libuarte1
LCD on SPI2
Sdcard on SPI 1,
I'm using ANT and softdevice 340,
When I run LCD and SDcard outside the main loop...
Hi,
I am having problems with the ble_advertising_int() function. It returns a return code of 12 (NRF_ERROR_DATA_SIZE) which is returned by ble_advertising_init() -> ble_advdata_encode...
