I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello .
I am looking for a way to pass the calendar time from the PC by the emulator to the MCU on first run.
I am using Segger Embedded studio 4.12
Is there a function...
I get the following error when launching the app, and the "Start scan" button either doesn't do anything or can't be clicked.
Error while probing devices: Error occured...
Hi
I am measuring the current consumption (with an amperemeter) of the nRF52 on the PCA10056 Devboard. The nRF52840 is supplied directly by connecting the external power...
Hi,
I have a problem when I do a write request on a 20 bytes characteristic from a custom service.
The funtion sd_ble_gattc_write return error 0x7 but I can't find what...
I want to stream a mono audio signal with high bandwidth (20kHz) from a remote device to a base device.
Need to A2D signal on remote and D2A the signal on the base. Low...
Hi,
The SEGGER have released a JLink software version that support to use JLink on ARM Linux platform。
I try it on raspberry pi, and it work well. But when i use pynrfjprog...
Hello.
I have a project that use the NRF_LOG_INFO for printing messages, and it is work O.K.
Now I add a part that need also to get parameters from the terminal.
I can...
Hi
Please advise when I can find firmware for nRF52840-DK which can send advertising packets or any data packets at data rate 125Kbps and +8dBm output power
I have two...
Hallo Everyone
We have developed a firmware for our systems using the nRF52832 with BLE 4.0.
Now we need to move to BLE 5.0. As far as I know the nRF52832 works with...
I get a strange error message reading from my hdc 1080 temp/rh sensor:
[00:08:38.013,916] <err> i2c_nrfx_twim: Error 195952641 occurred for message 0
I csnnot find any...
Hello Everyone,
I am working with nRF52832 chip on our custom board. I am using SDK 14.2 and SD v5.0.0 for development on a windows platform with Segger ES.
I am looking...
Hello all, I'm using nRF52 DK.
I'm going to use this DK as a master of BLE, and send information which is from BLE peripheral device to another board using SPI.
Anyway...
I am trying to implement the MAX30105 pulse oximeter sensor along with the Nordic Thingy 52 application source.
I referred the sample ADXL375 code provided by Simon here...
