Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi
I have tried to reproduce the 2.7µA current consumption stated in the datasheet. This webinar shows that the UDP sample reaches 2.7µA on the nRF9160 evaluation kit. However...
Hello Nordic! My question probably a simple one but I'm a novice so there's it. I'm looking for a way to get a GPIO port state that was at the moment of GPIOTE event triggering...
Dear Nordic Support
We have an existing Project that uses the nRF9160 SoC and builds with toolchain v2.4.4 and SDK v2.4.4.
The project basically runs with the nRF9160...
Hello,
My DK stop working as programmer suddenly.
the VDD power is normal with 2.9V and the V5.
Try already to power on with reset button hold.
blinking is not Consitency...
Hi Support Team
We meet an issue like the screenshot below when I program nRF52840 chip via the SES.
The SES version is v5.42a.
The J-link we used to program is...
hi:
asset_tracker_v2\src\modules\led_module.c
I only found the file that calls the LEDs, I didn't find the specific initialization and control code? Can you tell me how...
Hello everyone, a pleasure and very grateful to be able to write in this forum.
I am trying to program a Nordic BLE device so that it does not appear in the pairing list...
Hello, I am developing a board using the nRF52840 QFN48 and powering it using a 3.7V single cell LiPo battery. Since the battery voltage is stepped down to 3.3V via an external...
Hi.
I would like con build nrf Connect OT COAP Client and Server on a zephyr 4.0.99 / toolchain: zephyr 0.17.0
I have downloaded nrf sdk 2.9.99
running:
west build...
Testing the RADIO TEXT example on 52811.
1. 52811 is not a supported target - so I must select all targets then the unsupported dts (nrf52840/nrf52811)
2. I add a Build...
Dear Team,
Is it possible to run BIS and PAwR concurrently while using PAST for synchronization? I am using the nRF52840 DK and NCS 2.8.
I managed to start two periodic...
I am working wih \nrf5_sdk_17.1.0_ddde560\examples\802_15_4\wireless_uart\secure\first\
And I want to add app timer to start a peroid works.
unfortunately， this timer...
Hi Q&A
At present, there is no routine found on the Internet about NRF52832 Bluetooth sending more than 6 characters(NKRO)
I used nRF5_SDK_17.1.0， The following is the...
