Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I am trying to use SST26VF064B IC in my project (We use nrf-sdk-16 ). we use a driver code that was already tried and tested with the stm32 controller. But when trying to...
I want to detect the button short press and long press.
When short press is "released", trigger LED mode 1.
When detect 3 sec long press, start edit mode.
It seems GPIOE...
Just the title, the cloud website returns error code 40412 Just like in the instructions, input field is nrf-XXXXXXXXXXXXXXX where "X" is the 15 digit IMEI on the back of...
We have been developing with the nrf9160 for a bit and now you guys pulled a stunt which is very weird. We are about to go in to production and you released a new version...
I'm putting together a prototype using the nRF52 DK and the Adafruit Sharp Memory LCD board. I need to send SPI commands to communicate with the display.
I've installed...
Hi,
I tried to run a quick test to see if NVS functionality works out of the box when adding it to the tfm_ipc sample in Zephyr and it seems that my call to nvs_init hangs...
Hi Nordic,
I've tried to do some long duration measurements first 5 days, but also just 24 hours. Both times the Power Profiler desktop app was still running when i came...
This is just general feedback about the Infocenter documentation. When multiple tabs are open, or for bookmarking purposes, it would be nice if the webpage title changed to...
Hi We are developing a project where we are using a peripheral over i2c, specifically a lis3dh accelerometer. However we have encountered a problem and would be really grateful...
I want to set more features in a single service, but once there are more than four features, some features will fail and no error will be reported. Some features in the service...
Hi suport team
1、My ADC sampling circuit is shown in the figure below.
2、The actual voltage at ADC sampling is 1.37v, but the voltage measured by ADC is only 1.29v....
After programming the sample to my nRF9160 DK, I opened the terminal emulator and I observed the following messages:
1. HTTPS client sample started
2. Provisioning certificate...
I have tried the nus relay experimental example using nrf52dk and sdk 17. However it crashes when I try to connect using either nrfToolbox Uart or BlueFruit Connect (Uart...
Hello. I'm sorry for my bad English. I'm currently working on a development using nRF52840 based on ble_app_blinky, which is an example of s140 and peripheral. So, I want...
2. In the nRF sniffer software, the device I'm interested in does not show up in the "Source" column with its addess, b8:80:4f:6b:b6:9e, but as "TexasIns_6b:b6:9e". It seems...
