Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi, I have a SIM800L GSM/GPRS module that I can successfully talk to via the UART on the nRF51.
I can tell it to dial numbers etc and that all works fine.
My problem...
Hi, I'm using app_pwm with 32.768Khz external xtal. the following is my setting in sdk_config.h.
// <0=> RC // <1=> XTAL // <2=> Synth
#ifndef CLOCK_CONFIG_LF_SRC #define...
Hi,
I used sdk 15.2.0 version, I refer to the ATT_MTU Throughput Example to modify the Nordic UART Service (NUS) Application example.
Now I have some questions:
1. How...
Hello,
I'm using nRF52832, SDK15.0.0, Softdevice S132.
What should be the code added to application in order to support BLE DFU service?
I've been here , but its for...
hello,
I want to use RSSI on nrf52832, and the project is uploaded.
the question is, I test the RSSI on channel 2468MHZ， the NRF_RADIO->RSSISAMPLE result is about -92dBm...
Hi,
I followed the instructions for Getting Started with the NRF9160, activating the iBasis SIM card, placing into the board and applying USB power.
The first issue...
Hi,
I'm trying to update the firmware on my nRF9160 development kit
I downloaded the modem firmware and DFU tool
And then tried to follow these instructions: ...
Hi,
I want to activate eDRX on mqtt_simple example and measure the current consumption. I guess based on the code, by enabling "CONFIG_LTE_EDRX_REQ" it will be activated...
Hi guys,
I know that there is no official support for C++ on NordicSemi side, but I just wonder if it would be possible to work with C++ in Segger IDE. I'm trying to integrate...
SDK version: nRF5_SDK_15.3.0
Platform: nRF52840 DK
SoftDevice: s140
--
Hi All,
I use ble_app_blinky example and Android nRF Blinky SDK to add new function.
Recently...
Hello,
I'm using NRF52840 module to make a customer device. This device send message by UART. My device is powered with a battery, for this reason I would like reduce the...
Hi All,
We are using NRF52832 in our project. We have implemented the c code to perform nrfutil operations.
We are following below steps to do it.
Erase all files...
Hi, I'm doing some tests with Legacy OOB and I made it work with Master Control Panel 3.10.0.14, but when I try with nRF Connect v2.6.2 it fails. I know MCP is not supported...
Hi nordic,
Please inform bjorn-spockeli to reply in this thread its very urgent
https://devzone.nordicsemi.com/f/nordic-q-a/45470/encryption-and-decryption-of-advertising...
i working on a project of buttonless dfu on nrf52832 dk. so face a problem that after dfu the uart service is not show on nrf connect app. so i not be able to receive data...
