Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I have two nearly identical revisions of a board with an nrf5340 which behave differently in a curious way:
On one revision I can issue a "mon reset" command in...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hello, I am developing nRF5340, the project is pre-production. I am getting a issue with BLE power consumption, when I turned BLE on, the current is about 9uA. with BLE beacon...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
Hi Friend,
I am using nRF54L15-DK,NCS2.9.1 to drive INMP441 to collect voice. I take the I2S_echo Zephyr example as base. I can found the config a s below but it doesn't...
Hi
I am working on a BLE repeater which is central and peripheral application. which will scan and connecting with sensor device , and advertising for phone connection....
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
[ Just figured out it doesn't work the way I thought ]
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
