Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
Greetings,
I have worked with the MCUBoot and its Serial Recovery feature with success and recently tried to enable the CONFIG_BOOT_SERIAL_WAIT_FOR_DFU option ( as well...
Hello,
I am intending to extract audio from the onboard microphone of nrf5340-audio-dk.
I used the nrf5340_audio application as reference but cutting off the bluetooth...
Hi,
I'm trying to use same UART channel on both project-specific purpose and MCUmgr DFU. However, when I enable the option CONFIG_MCUMGR_TRANSPORT_UART, the code reset's...
Hi, I used in my hw design Config. 6 for nRF52840 QIAA aQFN73
https://docs.nordicsemi.com/bundle/ps_nrf52840/page/ref_circuitry.html#ariaid-title7
The question is how...
Hi,
We are defining a BLE interface for our product, choosing SIG and custom services, and while working on BLE for years now, I have still questions on how to design the...
How to configure the SPIM if i have defined my MOSI/MISO/SCK pins in the device overlay file, shown below:
&pinctrl { spi0_default: spi0_default { group1 { psels = <NRF_PSEL...
We are developing a board with an nRF54L15 module that interfaces with a SPI device. We want to use 3-wire spi, so the MISO and MOSI lines are shorted (according to the datasheet...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2.
I am currently using Pawr. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hello Nordic Support,
Currently, we are using nRF5 SDK for Thread and Zigbee 4.2.0 for our Zigbee coordinator application running on nrf52840.
We understand that this...
I am using the NRF5340 Audio DK , and the onboard PMIC is the NPM1100 . I am not using the onboard audio codec of the DK. Instead, I am powering an external audio codec module...
Hi,
I've just completed Lesson 2 Exercise 3 and found that BLE Provisioning does not work from the iPhone version of the app. The problem seems to be related to Version...
Hi everyone,
Environment:
nRF Connect SDK v2.8.0
Light Switch example
I’m currently working on implementing a Zigbee Sleepy End Device (SED) for a battery-operated...
Hello,
I'm currently using the nRF9151-DK hardware to develop our product based on the nRF9151 SiP . We selected the ncs-serial-modem firmware, and the modem is controlled...
I am implementing the code for nrf54l15 nordic MCU to: Use vbat_mon pin p1.10 in NRF54L15 as ADC and trying to read the voltages, but physically i am not able to read/get...
Hi,
I'm using nrf54l15 SOC with Zephyr NCS SDK to build a BLE application. I want to set the radio Tx Power to be set to as high as possible as our device will be enclosed...
