I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
Hi,
I recently followed the instructions to install nRF Connect on Visual Studio by completing Exercise 1 of the nRF Connect SDK Fundamentals course: Exercise 1-1
I noticed...
I am trying to set CONFIG_TFM_BL2 and it seems like it cannot be set to 'y' because CONFIG_TFM_BL2_NOT_SUPPORTED is also set to 'y' in ${prj_name}/build/${prj_name}/zephyr...
I am using the nRF7002-DK to implement a BLE interface. I need to send packets > 23 bytes through a notification characteristic. I am currently using nRF Connect on an android...
Hello, I am using nrf52832 along with S132 soft device and SDK 17.1.0.
Can you please provide me the peer manager api that can list the paired/bonded devices? Also, is...
Hi,
I would like to ask a few things about Channel Sounding (CS):
Is there any recommendation which method (IFFT, PBR, RTT) should be used for reading the results...
Hi
I`m working with an nRF52833.
I've observed that when the module enters DFU mode, the Bluetooth advertising name seems to be limited to around 22 characters.
If I...
I am trying to run the WiFi Station sample, unchanged on a nrf7002DK, but receive the following error: "wifi_supplicant: Failed to add iface wlan0" Complete output as follows...
I’m currently experiencing an issue while trying to install the Toolchain Manager application from nRF Connect for Desktop (v5.2.0) on Windows 11.
Every time I attempt to...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
I’m having an issue using QSPI flash with NRF Connect SDK 3.1.1. I have two PCB versions with nRF52840 MCUs — one uses the W25Q128JVEM chip and the other uses the W25Q128JVPIQ...
I want to connect a W25Q01JVZEIM (128MB) NOR Flash ROM to SPI3 of the nRF52833 and implement USB MSC functionality. However, the build fails. It seems the overlay description...
I'm communicating to the nPM1300 eval kit over I2C from an nRf52833 DK (running a fuel gauge application). This works well until I connect PowerUp (through USB) and enable...
Hello to everyone!
I bought nRF54L15-DK for Matter Over Thread developing and prototyping.
Before nRF54L15 I tried ESP32C6 XIAO + Arduino IDE and it worked but it was...
Hey, I have an nrf52840, with lis2dh sensor.
I configured the sensor using the devicetree using the following code
and I change the sensetivity and some other register...
