I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
We have generated a .hex file to be programmed to the external QSPI flash on the QSPI bus of an nRF5340, using the same MX25 part as used on the DVK (8MB/64Mbit) but with...
Hello Team,
Need urgent support for the nRF52840-DK.
I want to develop a program for the above mentioned kit for green power zigbee communication. This DK will communicate...
I was testing 9160 power consumption, the specifications says it is the minimum consumption current 7µA, but when I test on the DK board, the minimum current is 2ma, my test...
Greetings, I designed custom board using nRF52832 and sht20 temperature sensor. I defined sda and scl pin number of sht20 in pca board file (pin number 23 and 24). 4.7k pull...
Hello,
I want to test cold start performance of GPS on the nRF9160 DK using the gps example from the SDK. If I run the example unmodified from the sdk, get a fix, power...
Hello!
I am working on a project where we want over the air updates for the finished product. To make that possible I implemented the buttonless DFU and it is working great...
By following this post , I had some issues.
When compiling nrf_ppi.h:
1) For channels 10, 11, 12, 13, 14, 15: 'PPI_CHEN_CH10_Pos' undeclared here (not in a function...
Hello !!
I have custom board on nrf52832 having 10 buttons which is pull down by default. I have achieved 22uA after modifying the ble_app_beacon example to broadcast when...
I am writing a program by moving the contents of twi_master_using_nrf_twi_mngr based on the ble_app_uart project.
The source code is as follows.
Please tell me how...
Hi, 1- I have worked on ble_app_template(As Peripheral Only). Now, what changes I should make to gain max range? Any specific changes for long-range? 2- Here is my code. I...
Hi I am using ncs version 1.5.0 and dk version 0.15.0
I want go get the modem info like MCC,MNC,CellID & LAC..I followed the following snippet
err = modem_info_string_get...
Hi,
I am able to sniff and decrypt all the packets in Mesh Network as per NRF_Sniff Procedure Manual.
But unable to decrypt the packets received between the Low Power...
I'm developing an application where there will be multiple central links to relatively low bandwidth sensors and 1 central link where sensor data will be streamed. The throughput...
Hi teams,
I am developing with Mesh SDK 4.0.0, and suffers from random fault during long-term test.
The last readable callstack position is the below.
The callstack...
