[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nRF51-DK with nRF51422 with softdevice S130 and SDK 12.3.0.
I see that GPIOTE driver provides sensing for signal transitions like NRF_GPIOTE_POLARITY_LOTOHI...
Hi,
I have setup the Segger Embedded Studio for ARM (Nordic Edition) V5.10d, and managed to compile a sample app from ,
V1.4.2 -> nrf -> samples -> bluetooth -> peripheral...
Hello,
I have different behaviour with 2 identical boards.
They behave differently (at least for BLE functions).
With jlink interface, I saved the flash binary of...
I have installed the toolchain according to nRF Connect guideline, on my MAC OSX.
My option settings are listed in the attached image.
I downloaded release 1.4.2.
...
Hi Sir
We are developing a product with nRF5340,
Now we faced the PCB layout symbol creation issue,
I can't find any information about footprint of nRF5340,
Can someone...
Hello,
I am trying to get acquire the accelerometer data every 4 hours for a sample duration of 60secs. These data are stored in RAM and on ble connection with the mobile...
Hi,
I'm totally new to programming nRF DK's.
What am I using?
Segger Embbedded Studio for ARM (Nordic Edition)
Toolchain: nRF Connect SDK v1.4.99-dev1
The "mqtt...
Hello there,
Since we use the lower level modules from Nordic's SDK for Mesh 4.2.0 - namely timeslot.c, bearer_handler.c and some additional modules to make them work properly...
Hi,
I just happened to stumble across these lines (123 to 126) in nrf_drv_uart.h:
And I noticed that on line 125 NRF_UART_ERROR_FRAMING_MASK is mapped to NRF_UARTE_ERROR_PARITY_MASK...
Hi, I've got our custom board with W25M02GVZEIG and I want to be able to read it out in a way that is fast and works with XIP. It's ok if it takes more time to write.
So...
Hi, I've made UART (BAUD RATE 1M) only on central after recieve all data (8kB). Peripheral is sending data from own ram (collected data from SPI sensors). What and how i need...
Hi,
I am trying to start from scratch BLE firmware to send and receive data from the development kit PCA10100 and nRFConnect App. I am following this course on Github here...
Hi,
i am trying to send temperature data along with timestamp as a string over BLE to a smartphone. i did the temperature reading part and now want to add timestamps to...
Can you show how can I merge the ble_app_uart and ble_app_uart_c into one code?
Once the device wakes up, it will check its GPIO - if it is '0', the peripheral will start...
