Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hello,
I'm working on a BLE app on an Arduino Nano 33 BLE, which is equiped with an nrf52840. I'm struggling to increase my BLE transfer speed ( i think due to the limitations...
Actually i was working on 3 boards, nRF51422,nRF51822 & nRF52840. While executing some examples on each board i realised that each board has its specific pca hex file to be...
I n the main of my program I have this( UBLOX_PWR_PIN = Pin16 of nrf ),
uart_init(); nrf_gpio_cfg_output(UBLOX_PWR_PIN); nrf_gpio_pin_set(UBLOX_PWR_PIN); nrf_delay_ms(200...
Hello,
I've a problem with a PPK board.
When the current go over 10mA the value reported is wrong, in my case should be 15mA and PPK measure 80mA and more. Instead, in...
Hello,
I am working on a project that is using nrf52840 chip as a peripheral and the product is supposed to last and run for 25 years. During that period the device will...
Hi everyone I have been reading the GPS data using nordic nrf52840 over the UART. I am able to receive as much as 64KB of data via the UART. Here's the scenario of whats been...
Hi All:
Applyed the under timeslot :
causes some peripherals(eg:static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(2)) n o access interrupt,
what 's the...
I am trying to get the maximum Tx power from the nRF5340 PDK.
The nRF5340 specifications say that setting VREGRADIO.VREQH is required to get the last +3dBm of transmit power...
Hi,
I know that this topic has been raised here many times, and I did read all of those threads, however none of them seem to solve my problem. As many others, what I am...
Hello,
I got my hand on the nRF9160 DK 0.9.0 and was able to connect it correctly to the nRF connect cloud.
I followed the nRF Connect for Cloud Certificate Update and...
Our repository is hosted at github and we are developing and building with Segger Embedded Studio.
Is there any documentation for setting up CI with github actions, travis...
is it possible to access application logs via the SWD interface?
For eg: i see code like NRF_LOG_INFO("Temperature example started.");
Can i see this just by connecting...
Hello everyone.
I use nRF52840 and Segger Embedded Studio. This is my first MCU development.
Thanks to the SDK, I was able to use GPIO, twi, etc.
I am interested in...
We have noticed that using nrfjprog for programming 52840 based devices (and the devkit) that programming times are longer than with 52832 based devices with the same size...
I am trying to switch leds on and off on my nrf51822 beacon kit using an android application to be made by me.
I am not able to get any similar example.
Also i want to...
