I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hi!
Can anyone from Nordic pinpoint where exactly in buttonless project or bootloader project NRF_DFU_SVCI_ENABLED definition is used? I mean 15.0 and 15.2 SDK.
I have...
Hi, i need an advice.
It said in nRF51822 datasheet at p.11.1 (PCB guidelines) that "The supply voltage for the chip should be filtered and routed separately from the supply...
I have upgraded to the more recent J-link RTT Viewer.
If I start Debug Session in uVision and run RTT Viewer, I can connect just fine and have checked the Existing Session...
In the nrf5 sdk (version 11.0.0) there are three different modules which, as near as I can tell, do the same thing. These are:
pstorage
fstorage
ble_flash
...
hi........... nrf523
how to read the data from peripheral and send the data over ble using ble uart
i have merged the two programs ble_uart and twi sensor ,what changes...
Hi,
I'm trying to flash the mesh lightswitch example on Bluemod S42 custom board, please help me with what are the steps to be taken to flash on custom board.
Hi,
As the tile says, I'm using BPA600 capturing mesh logs and analyze.
Since BPA600 needs to configure "MeshOptions.ini" to be able to decode the logs, it needs "IVindex...
Hi
I would like to debugg my Nordic (nRF52832) custom board at 1.8V with a 6 pin Tag-connect connector ( see here ) and have a couple of questions regarding...
Hi,
I'm trying to compile a simple example (light_switch_dimming_server_nrf52832_xxAA_s132_6.0.0) for Bluetooth mesh with Segger embedded studio. I'm having a hard time...
Hello,
I have a twi module developped using sdk v13. I want to upgrade it to the sdk 15 to integrate it to a mesh project.
I changed all nrf_drv functions to nrfx same...
can I make indoor localization with nrf52840 DK board without an android app,
suppose I am using 3 devices for localization of the 4th device, and I need to get RSSI of...
I want to make infrared transmission and reception function with nrf51822.
I want to know how to make TImer part using NEC protocol.
Tell me how to implement this feature...
Hi,
I am working with nrf52832 DK,softdevice s132.SDK15.
I was following "nRF_Sniffer_User_Guide_v2.0.pdf" to set up nRF Sniffer.
But in the Wireshark Application under...
Hi there,
This is a general question about addresses types in Bluetooth mesh and specs:
As far as I know, Bluetooth mesh specs talk about the 32767 nodes in the theoretical...