Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi!
I am trying to utilise the BLE SIG service for environmental sensing (0x181A) with the characteristics for temperature (0x2A6E) and humidity (0x2A6F). I would like to...
Hi
I'm trying to build blinky example (from SDK17.0.2) to run it on nRF52833DK.
The board is running correctly if I download the hex comes with SDK but failed if download...
Hi, I'm writing a library for the common Hitachi_HD44780 (LCD2004 etc) but need it to be non-blocking. I'll open source it once done. I'm using EasyDMA to do the transfers...
Hello,
I am trying to solve my issue for few days without success hence your help would be appreciated. I found a lot of related issues, but any of the solutions doesn't...
Hello,
I am using nRF52840 chipset and I was using the Segger tool chain properly. But recently I started getting below error "The evaluation period of this release has...
Hi,
I am doing the project in nRF2832 , where I need to collect some data from the sensor and temperature value that i need to save in the .CSV file format in SD cARD ....
Hi,
I have a question about setting the gpio pin status. From the picture, it seems that the value on the right represents the status of the gpio pin. So the default value...
I'm using NCS 1.4.0 and 2 boards nRF5340PDK.
I'm using central_uart and peripheral_uart samples. Both display when connection interval change.
The central_uart use BT_LE_CONN_PARAM...
can You explain
light_lc_client_light_onoff_set(&m_clients[0], &set_params,&transition_params);
This command in the lc client used to make the immediate on the server...
I'm implementing a project that attempts to change the TX power of itself during runtime. I have used the set and get functions from the Zephyr sample: https://docs.zephyrproject...
Hi guys, Do we have an outlook on silicon in which errata bugs 174, 195 & 198 (SPIM3 bugs) are solved?
Best regards,
Casper van Doorne
Pink Fluffy Unicorns BV
I am trying to make the LSM9DS1 connected with the nrf52840,
1. Now I am trying to send the hex array to the lsm9ds1, seems always failed.
any suggestion how to make...
Hi,
In my aplication, I bring my nRF52840 into power system off mode with s d_power_system_off on several different events, most notably the BLE_GAP_EVT_DISCONNECTED event...
Hi Team,
We have developed an application where we are able to receive scan request notification in peripheral and scan response notification in central.
Is it possible...
