[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
OVERRUN error occurs when receiving UART.
I'm using EasyDMA with UART and want to increase the EasyDMA reception size. Which settings can be used to increase the reception...
Hi,
I have NRF52833 DK and using nRF5 16 SDK on KEIL IDE.
I am trying to compile blinky example from the peripheral and it is giving me this error
Error #541: 'NordicSemiconductor...
During production we need to provision each device with some custom data that must last the life time of the device, ideally using nrfjprog. What is the best way to do this...
There are several use cases where we want a bonded peripheral to indicate the service changed characteristic to the central.
The main case is when developping and adding...
hello can someone help me solve this issue. i am not being able to controll this led . if i send any number the led will always turn on
Regards
static void led_col_write_handler...
Hello,
I want to test the range of Adafruit nRF52840 express feather(BLE 5.0) board. I did the setup on arduino IDE. My question is can I perform the long range test of...
Hi, we have a project that we're currently working on, and we're looking for some information on BLE behaviour that would be very helpful. We are currently using SDK 15.3...
I'm trying to build aws-fota program following this instruction, but get an error https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160/aws_fota...
I have a nRF52840 dongle.
My understanding is that the nRF52840 has an on-chip regulator (Vdd out) that can be set from 1.8 to 3.3V.
So it's recommended to use a debugger...
Hi
I am attempting to add nrf_crypto functionality to the example uart ble peripheral project via SEGGER Embedded Studio on MacOS.
I have opened the project options and...
I have two devices, one is a beacon (DEVICE #1) and the other (DEVICE #2) collects information from the beacon. I'm advertising with a transmit power of 4dBm. I want to reduce...
I have previously had success with programming the nRF51 Series using the nRF51 DK and want to use the nRF52840 DK to program a nRF52840 that will be run in High Voltage Mode...
From the cmakelists of bootloader in Meshv320src, I found the code "create_hex" but this code cannot found in CMake's document. How can it work to generate the hex file?
I am using SDK 15.3 and wanted to ask that if there is a while loop where I can check flags and increment tickers. The program at the moment gets stuck inside
Suggestions...
hello, I have two questions for SAADC of nrf52832 when we use nrf52832 SAADC for voltage measurement.
The AIN0 is connected to the pin to be measured(the voltage is about...
