Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
I had even erase application firmware as well as modem firmware and reprogrammed it. This device working properly before but during FOTA update due to some power supply error...
To the kind attention of Nordic support team,
I'm using sdk16 and usbd. Sometime I get
app_usbd_core.c -> usb_core_ep0_handler_check --> NRF_LOG_WARNING("Previous setup...
Hi All,
Now i'm using peripheral - blinky project,and i saw the Block allocator module in the sdk_config.h.
Can anyone tell me what is the Block allocator module use for...
Hi,
I met some problems when I tried the sample 'direction_finding_connectionless_rx' in ncs v1.7.1 on nRF5340dk. I copied files to hci_rpmsg/boards as https://developer...
Hi all,
I got my nrf5340PDK working with the Thread CLI Sample.
I can now connect to the UART interface and issue ot commands.
According to the tutorial Thread: CLI...
In response to a BLE_GAP_EVT_DATA_LENGTH_UPDATE_REQUEST, we have called sd_ble_gap_data_length_update, with the following parameters:
Rx Octets: 251/ Tx Octets: 251
Rx...
Hello everyone, i need to increment a counter each time my button on the nrf534DK is pressed i'm using sdk v 1.7.1 . is there a simple way to do it or a function which supports...
Hello!
I've seen similar posts about this issue: https://devzone.nordicsemi.com/f/nordic-q-a/57105/nrf9160-modem-stuck-in-searching https://devzone.nordicsemi.com/f/nordic...
I am looking to handle low priority interrupts on a single GPIOTE Port Event but when attempting to add the second pin with the same handler i get an error and the handler...
Hi Team Nordic and fellow engineers, I am seeking to find better parts from Nordic RF Transciever lineup
to replace nRF24L01P-R, in order to improve the performance of the...
Hello, I intend to use libuarte under FreeRTOS together with the SoftDevice (SDK 17.1.0). An app_timer is used for the RX timeout. I think there might be an incompatibility...
Hello,
I have a situation where I would like to reset the MCU (nRF52832) under Zephyr. For the most part I use ```sys_reboot(SYS_REBOOT_COLD)```. However, I would need...
Hi,
I just downloaded both versions 1.7.0 and 1.7.1. Compiling asset_tracker_v2 right out of the box with west build -b nrf9160dk_nrf9160_ns --pristine I get the hex files...
