Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
Hello, I'm designing a medical product, aiming at IEC 61000-4-2 level 4 ESD protection, and I have a question on the CC lines.
My understanding is that these two lines could...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
We are seeing our nrf54l15 based device remain in a high power mode after an ADC read using the latest v3.1 SDK (tested on both rc1 and rc2). This did not occur with the v3...
I've been trying to communicate with an external device which supports up to 25 Mhz on its SPI. So, to improve performance, I'm using the SPI3 at 16 Mhz. I have no issue at...
Hi,
I am trying to add an additional storage partition in flash to my project, however, to some reason, pm.yml file is not getting picked up during the build and I am not...
Hi:
I want to use nrf54l05 for the OTA function of BLE. In the example of l9_e5_stol, nrf54L15 OTA can running, but NRF54L05 cannot run.
NCS 3.0.0.
The part I modified...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
After updating to nRF Connect v3.1.0, I am not able to build a project that was started with v3.0.2, nor the matter template sample. When building both my application and...
Hello,
I have been evaluating the DECT NR+ physical layer with nRF9161DK boards with the v3.0.2 DECT Shell sample application. I am wondering if there are going to be any...
Hi Sir,
I have a question about these two configurations in overlay-ppp-cmux-linux.conf, CONFIG_MODEM_BACKEND_UART_ASYNC_RECEIVE_IDLE_TIMEOUT_MS and CONFIG_MODEM_BACKEND_UART_SLM_TRANSMIT_TIMEOUT_MS...
Hi,
I recently started working with the nRF9151 DK and was able to run the initial demo programs without any issues. To continue testing, I picked up a Thingy:91 X, but...
Good day, Nordic staff!
We are working on a product using the FLPR for its intended peripheral-controlling purpose. For us, the best way to send commands to and receive...
Greetings to everybody! There is some question about nRF54L15-DK board measured current consumption. I measure current via the P6 connector, that is, I measure current within...
