Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Dear all,
Hi, I'm Eric.
I m studying spi communication used nRF52832 base on SDK 14.2/example/spi.
That examsignal is below picture 1.
But I want to delay between...
Hi--
I noticed something rather peculiar on the built hex from segger that is programmed onto my nrf52832 chip (firmware image).
The hex looked as expected, until i got...
My ble_peripheral is bonded to ble_central, How do I upgrade at this time ? If you still use the mobile phone APP to upgrade, you need to erase the binding information, and...
Hello,
I encountered a problem when installing nRF_connect on a new computer. As shown in the picture, the attribute "middleware" of null could not be read. Opening all...
I am using as template the MQTT sample app from NRF Connect 1.3.0, for which I want to create my own application modules, I have added the .c files to src, but I am having...
Hello,
We are using the Serial port library with two UARTEs. It defines two instances of the serial port interface: one for receiving data, and one for sending data. After...
Subject pretty much explains the problem. One can just get power from a USB interface, but if I plug our nRF52840 into such an interface, it does not appear to boot into its...
I am trying to use serialization to connect an STM32F4 to an ISP1705. My goal is too connect to other BLE devices and read some measurements. I have tried a few of the examples...
I'm using an example project of the secure serial bootloader (pca10056_uart_debug) and changed some configuration for my custom board. I added RTT debugging and changed uart...
Hi,
One of our projects will use either a LFXO or the LFRC depending on the accuracy.
The product will be exposed to temperature differences ranging from approx. 0 ...
Hello!
I handle mpu6050 sensor in SDK v14. Output of sensor values was successful. And I'm going to use this value to get the angle of the sensor.
The code below is to...
I am using NRF Connect 3.5.0 to program PCA10059 but receive the following error on some dongles when using JLINK programmer
Error while probing devices: Error occured when...
Hi there,
I purchased the nRF52 DK, and I am going to study how to use basic tools.
However, there is a problem with recognition between the computer and the nRF52...
Hello! When I start the s132 device, it freezes from time to time. In debug mode, it does not exit the saadc_init () function;
I connected "hardfault.h" and "hardfault_genhf...
Hi,
I am using nRF52832 , and sdk 15.2 version. I am trying the start the advertisement using timer , once it is connected it should send the data , and should disconnect...
