Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I am working on a custom board with the nRF9160 SiP. It comes with pre-programmed modem firmware. Header pins for UART1 and UART2 are provided on the custom board. Is it possible...
This is a strange one. I had a custom PCB that included an MDBT42Q module. After I learned how to program it, it worked fine. I made a slight revision to the PCB, and this...
I'm implementing a function which enters sleep mode and wakes up by interrupt like below..
Is this correct way to enter sleep mode? Do you know any other better ways...
Window10 nrf tag: 1.2.0 SES v4.4.2a
I'm attempting to code a one-shot mqtt function, but it fails in v1.2.0 whiile it succeeded in v1.1.0. I coded the below main.c by modifying...
Hello ,
I was working on BLE mesh implementation, It would be helpful if there is information regarding current consumption of different mesh nodes ( low power node, friend...
Dear team:
1.So how can I increase transmission withou improving TX power As for the transmission distance of nRF52832, apart from improving the TX power, what is the better...
Hello,
There is a particular task I'd like to accomplish, and I have been looking into the nRF52840 to do it. In a nutshell, I want to build a bi-directional relay for USB...
Hi,
i downloaded new SDK14 with example, after i upload hex from example in ble_peripheral/ble_app_hrs
I use s132 / nrf52
program stuck here :
ret_code_t nrf_sdh_enable_request...
Linker script `nrf_common.ld` in nRF5 SDK v16 defines __etext to point to the end of the .text section. It needs to be 4-byte aligned according to comments in `gcc_startup_xxxx...
Hello,
In order to try and implement passkeys, I've implemented my program inside of the glucose app example. The project compiles + runs and crashes sometimes randomly...
Hello everyone, just a quick question.
When routing on the nrf52832 WLCSP package, I noticed that the only inner pin "required" for use is the pin to enable DC/DC (Pin B6...
Hey guys,
I want to create an accurate timer without interrupts. My timer has to be very accurate because I have to send HIGH and LOW signals for 1us. I have read this pos...
Hello.
Currently I am trying to merge the peripheral example ble_uart and saadc examle. My little project is to send potentiometer values over ble.
As of now I have copied...
I have the bmdware.uvprojx project opened in Keil uVision 5 and have the BMD 350 breakout board containing the nRF52832 chip connected to my PC via a J Link debugger (EDU...
Hi all,
Here I am using the nrf52840 in my customized board, in parallel i have nrf52840 dev board.
I am using the twi peripheral to communicate with a i2c based sensor...
