Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
Hello Everyone,
I'm a beginner for nRF52 and my aim is to learn and develop system on nRF52. I have bought nRF52 development board and installed Keil MDK on my system....
Previously i've been using the nRF dongle using the BLE NUS Central example to communicate to another nRF DK with the BLE NUS Peripheral example via serial/termite and ble...
Hi there,
I am new to the nRF world and I might be asking a very stupid question with obvious answer but I couldn't find any hint from the Infocenter nor the Tutorials...
Hello guys,
I followed this guide to set up the software on my macbook.
The blinky example can be successfully built, but cannot be flashed to the nRF52 DK. Then I tried...
Hello everyone,
I tried to rename(right click the project name and click the "Rename") my project from "sdk11_ble_tutorial_adverstising" to "sdk11_ble_tutorial_adverstising1...
Hi,
anyone would have any idea (to look at, as to) why the same app running on the same chip/PCB (nrf51822QFAAH rev3) could possibly have slowed down so massively after...
I'm trying to add debug information to ble_app_hrs using nRF5 SDK 10, softdevice s110 version 8.0.0, building for an nRF51-DK target (PCA10028) using ARMGCC. I've found that...
I've encountered a problem getting the tick count from FreeRTOS when tickless idle is enabled. I'm not sure if this is a bug or just unexpected behavior. I am using the latest...
Hi everyone,
I'm integrating the spi_master_with_spi_slave example into our firmware; however, I'm not seeing the event callback I registered being called. I'm verifying...
Hi everyone,
I implemented nrf51 flashing through SWD (external MCU is used). After first flashing and reset when we enter debug mode on SWD second time we have a busy...
Hello,
I am trying to interface an MPU 6050 with an NRF52 with sdk vs 12.0. I noticed in the mpu6050.c file that it uses a twi_master.h file in the sdk in folder labeled...
Linking ble_app_proximity_pca10040_s132.elf
Output/nrf52832_xxaa/Exe/ble_app_proximity_pca10040_s132.elf section `.fs_data' will not fit in region `UNPLACED_SECTIONS'
...
Hi,
I flashed an board with a NRF52832-QFAA-R7 with the ble_app_hids_mouse of SDK 12.1 (and also with the keyboard) example to test and build an application using this...
Hi,
I've been trying to get an implementation of the HTTP Proxy working with nRF52. The nRF52 is in central mode, accessing the proxy (running on a Pi with Bleno) which...
i measured the current of nrf52 dk board with the spi example (examples\peripheral\spi\pca10040). the result shows that it consumed about 6 mA !!!
i read the nrf52 datasheet...
