Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Hi
I'm locking for an example like zephyr\samples\boards\nrf\system_off for nRF9160 DK
zephyr\samples\boards\nrf\system_off uses nRF51 DK or nRF52 DK board for the demo...
Dear support team,
I would like to use GPIO 09/10 as a GPIO interrupt.
I just searched and I see that need to define CONFIG_NFCT_PINS_AS_GPIOS.
But I can't do it. Please...
Hello, I'm making a system with NUS of nRF52832 and nRF52840 to sample data with SAADC. I started the system with "ble_app_uart__saadc_timer_driven__scan_mode_03" from Github...
Hello!
There is a sample simple_mqtt which is written for nrf9160 DK. Is it possible to make app_signed.hex file to load in thingy 91.
I tried to change prj.conf and have...
Hi,
Using the HRS peripheral example provided in SDK17 with S140 7.2.0, I am in the process of migrating to a custom board using nRF52833. I have already made some changes...
Hi,
Can you please tell me if Segger compiler initializes all variables to default values?
If so - can you please send me a link to that content?
Thanks
Hello,
My nRF52840 board is connected with SPI flash over SPI. I have configured the nordic as master and my SPI flash is slave as mentioned below:
Using the internal...
Hi,
I have a nRF52840 USB Dongle that I am using to perform OTA DFU to use to perform OTA DFU.
After the update is finished, the device keeps running the code instruction...
hi
I have written a driver for an SPI sensor, and it works perfect in a nrfx_spim example project.
But when I tried to add this driver to a ble custom project, errors...
I'm using the nRF5 SDK 12.3.0 on Linux (Fedora 33), with a minimal N51822 breakout board (nRF51822-QFAA(build code: H0) 256kB Flash, 16kB RAM). For programming I'm using a...
RTC 1 cannot be enable (errors with app_timer.c): Trying to resolve RTC errors
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with...
Excuse me:
Project in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard\pca10040e\s112\ses,After the device is connected, I call the sd_ble_gap_disconnect...
Hello, I'm developing a BLE mouse using nRF52840. I found something strange while testing mouse movement by connecting the BLE. I was logging using the RTTViewer and found...
Hello, here is the question about nrf52840_bitfields.h. Is there any problem with macros definition? For example we have such definition:
/* Bit 20 : Enable differential...
