In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
typedef struct __attribute((packed)) { uint8_t on_off; /**< State to set */ uint8_t tid; /**< Transaction number for application */ uint8_t transition_time; /**< Encoded transition...
Hi, We're connecting to our server over LTE and then immediately starting GPS search. The modem is in LTE+GPS mode. As we understand it, the GPS will do nothing for about...
<environment> - Windows10 - modem fw v1.2.0 - nrf v1.3.0
I try to get mnc and mcc data but no luck. Any help?
I also tried it using modem_info_params_init and modem_info_params_get...
There are 10000 posts with this problem. I have imported someone else's project, and the file exists at Keil_v5\ARM\Packs\ARM\CMSIS\5.7.0\CMSIS\Core\Include exactly where...
Hi all,
I've been trying to get BLE up and running on our custom board after writing firmware on the DK. I am able to get other peripherals on our board up and running ...
Hi guys,
I am a long term Nordic user since SDK12 and i know that Nordic does not support MbedOS by any means but maybe you could help me try and understand what needs to...
Hello,
I've a very strange problem with the nrf52838 chip in the ISP4520 ( https://www.insightsip.com/products/combo-smart-modules/isp4520 ).
The nrf52832 advertise...
Hi,
I need to sample ultrasonic signal with PDM microphone. I would like to use NRF52840 PDM module and configure it for sampling frequency of 96KHz. Is it possible? Also...
Hi,
I have used BMD301 BLE chip. I have connected one wifi chip "ESP02" with BMD301 chip via UART.
I am using nRF5_SDK_15.3.0_59ac345 for my ble application firmware...
Hi,
we have a nRF52 DK getting sensor values from a Sensor connected as SPI-Slave. Everytime there is a new Sensor Value (~20 ms) the sensor generates an Interrupt and pulls...
Hi,
While upmerging our project from SDK 15.3.0 to 17.0.0 we faced an issue in the sdc_handler due to usage of a NULL pointer.
In the case SDC_EVT_INIT if the p_event...
Hello,
I am experimenting with PWM for time, I have a setup where I am using three sensor which gives analogue output.
I am using a mux which has two control pins, so...
Hi all
I have just started doing some work with the nRF52840- DONGLE (and hence nRF52840-DK) and am new to Nordic devices, tools, BLE, etc.
Basically for my first application...
I'm attempting to increase the size of the TX Queue in an effort to increase notification performance.
I'm using nRF52840 with an S140 soft device. I use Segger Embedded...
