In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hello,
I'm trying to setup interrupt routines in SPIS1 peripheral.
I have a void IRQ function
But it seems like it never gets called
my init function
some...
Hi,
As I understand Nordic NCS now supports nRF52 development for nrf52832/40/11/10, so based on this I am trying to make a simple application for nRF5232 chip (peripheral_uart...
Hello,
I've been using http/https for some time with Zephyr, and am now venturing into using LTE/NB-IoT on a NRF9160DK board.
Unfortunately, from what I can tell, the...
Hi,
We are working on a Thread network application using nRF52840 DK and would like to interface a WiFi module to this board. We have checked the DevZone and found one similar...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi,
I have added the Buttonless Secure DFU service to my application so that the app can be updated over BLE. It seems working. However, the power management module must...
Hi,
1. In my last post, ( https://devzone.nordicsemi.com/f/nordic-q-a/60300/questions-on-usbd_cdc_acm-example ), in question #1 a nice explanation was given regarding the...
Hi,
I am wondering if there solution available to perform DFU using Windows 10 OS? Going through previous tickets, it seems that there is no easy solution to perform DFU...
Support,
I am using the ble_app_gls_pac19956_140 example on the nRF 52840 DK. I wish to use this application as a foundation for my new sensor.
I wanted to disable the...
SDK: 15.2 IDE: Keil Softdevice: S132 v 6.0 General question about PPI connections. Is it possible to setup a PPI channel, that when triggered by some event (e.g. value in...
Hi,
I'm trying to lower the power consumption om an Actinius Icarus board which uses an nrf9160 chip. I've been able to achieve a sleep current of 1.33mA and I'm not able...
Now the code in the application part has added the buttonless_dfu function, which has also been successfully implemented. But I ’m not familiar with serial_dfu, I don’t know...
Good Afternoon:
We are developing a BLE remote button using Nordic's nrf52840. We have purchased several devkits and are in the process of fabricating our own design specific...
Dear,
Im trying to use the motion to activate the GPS and deactivate GPS:
1. when it moves, GPS will be activated: Position-ON
2. when it stops, GPS will be activated...
