Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Hi there, thanks for your help in advance!
I have tried the nrf51-ble-ancs-nus sample from github and making it work on a 51822 EK board, i.e., it can receive notifications...
I try to use hcidump, capture CSR dongle on ubuntu14.4.
I can find SDK8.1.1 s110 keypad demo create connection fail.
HCI Event: Command Complete (0x0e) plen 4
LE Set...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Hello everyone,
I am trying to communicate among 2 NRF24L01+ modules using 2 ATmega16A microcontrollers.
My SPI communication is working fine as I am able to write and...
Hello,
Is it possible to receive a review for a board i'm developing??
This board is to be used as a Raspberry Pi Hat to be able to communicate using UART between RPi...
How to recover communication due sequence number. (Could be due of PYACI serial hardware changed/dammaged). Is there any command to reset or know sequence number of node....
Hello all,
I'm developing a BLE CGMS application based on the experimental example on the SDK folder.
Now I working in the timing characteristics and I could see that...
It looks to me like there's usage of the 32 bit milisecond timer in the mqtt client.
It seems to me that mqtt_elapsed_time_in_ms_get(...) could calculate an incorrect elapsed...
We're using the nRF9160 with an external main microcontroller, and communicating with it over SPI. We're evaluating the lowest power modes of our custom hardware to make sure...
1. I want to minimize current consumption (5uA - 10uA) in nrf52832.
2. We are using the soft devices in it.
3. Please tell me all possible SDK configuration settings for...
Hello all,
I have a BLE central application based on nRF Connect SDK V1.6.1 and a BLE peripheral application based on nRF5 SDK 17.1.0. The peripheral wakes up on interrupt...
Hi
For the qualification we need to know the values of the parameters listed below. Our hardware uses a nRF52805 and can operate in both ESB and BLE mode.
Operating...
Hello Devzome Users,
I have a problem with running my codes on other computers. The project runs on my PC very well which I coded original.
I would like to test it on...
Hello Nordic,
I've acquired several nrf52-dks and I use them almost exclusively to flash with nrfConnect on the PC.
To learn more about nrf programming I started with...
Hi all,
May I know is the antenna array a built in in 5340 DK or not? According to https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_connectionless_rx...
Hey all, I've been learning/working on the 53 and have had some issues adding in the AMG8 example. i've gotten the sensor to work flawlessly on an STM32 & nordic 52 but am...
Hello to all,
I have a question about parsing zigbee commands when they present a payload.
In the Window Covering device I use the define "ZB_ZCL_WINDOW_COVERING_GET_GO_TO_LIFT_PERCENTAGE_REQ...
Hi support team,
I'm learning about distance calculation based on time of flight. I only have nrf52832DK here but i wanted to try. I'm looking for an example of getting...
Hello,
Power Profiler v3.1.3
Windows 10 Home 21H1
On Data Logger tab and , regardless of if a PPK2 has been connected or not, and regardless of any of the values...
