Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
I am trying to generate ECC key pairs using MbedTLS on Connect SDK.
I found this code block on stackoverflow and validated from mbedtls/programs.
"mbedtls_ctr_drbg_seed...
I was trying to evluate the Periperhral ISO server, however with a NR52dk, but it returns ENOTSUP.
Bluetooth initialized Unable to register ISO server (err -134) [00...
Hi all
I am developing a proprietary radio protocol application using the nRF52805. I am not using a softdevice. Instead, this is all done by accessing the radio registers...
I have seen this question answered for the old Nordic SDK but have not been able to find a solution in Zephyr & NCS. I'm following this post on how to develop a custom BLE...
Hello,
i am using nrf52832 dev kit want to send the nrf calendar parameter through nrf connect app and send through app successfully by taking uint8_t datatype .I have receive...
Hello.
I am trying to write code to read data using saadc and write the sampled data in a micro SD card using fatfs.
I started from the fatfs example and initialized...
I'm attempting to use pc-ble-driver-py on Windows with an NRF52 DK (PCA10040) and running into the error shown below. Using the Heart Rate Collector example, the COM port...
Hi,
I'm using the ble nus uart for my application and I noticed that I was drawing too much current so I went back to the example from the SDK 17.0.2_d674dde which I haven...
I have followed the Azure IoT Hub — nRF Connect SDK 1.6.99 documentation (nordicsemi.com) and was able to comminicate with Azure IoT hub.I have created rootCA and device certificates...
This is my problem description, hope someone can help me. 1. The watch product shipped in mass production is found to be disconnected when using the mobile phone OPPO-k7x...
HI,
i have enabled CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE=y
so after power cycle the device automatically connects with iphone and the service also works fine
after this...
Dear Nordic,
Could you please help me to understand the concept of using the DTS files and board initialization sequence?
We have just one GPIO port to control some external...
I suspect the EXT_SWCLK/DIO and SH_SWCLK/DIO pins on the SEGGER chips of the PCA10028 were burned. Is there anyway I can fix it? I have three of them behaving the same way...
