Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
I have an NRF52840 DK (3.0.2) board, but it is not working. The USB port is not detected. When I power it through USB, the debug LED (LED5) turns on and then off. On the SoC...
Hi，
SDK:ncs2.6.1. The main program runs in the app core, and the net core is included as a child image. The Bluetooth broadcast is normal when tested at room temperature...
Hello Team,
I am trying to measure the sleep current of NRF54L15 DK, in the system ON mode, for that I am using Blinky sample code, from SDK version 2.9, which uses the...
Hello,
i recently received several nRF54L15DK kits.
The example good for channel sounding works well but left us with a question about the BLE antenna.
According to...
Hello when I build an application on VS Code, the terminal give this error :
warning: UPDATEABLE_IMAGE_NUMBER (defined at C:/ncs/v2.8.0/nrf\samples\common\mcumgr_bt_ota_dfu...
Do we have documentation anywhere detailing which pin is used or not in the 9161 DK and 7002 DK? I see docs like this:
Board control
Buttons and LEDs
I selected pin...
Hello ,
i m using sdk 15.0.0 and spi example for flash winbond 25q64 read write .
i m successfully read manufacture id,,device id.
but problem is writing and reading...
I'd like to know if the below info. is correct.
QDID of the nRF5340 chip itself : 11524
QDID of the Host system used in nRF Connect SDK version 2.8.0: Q322804
BR...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, to ensure that the connected...
I am currently working on a custom board with the nRF9160. The modem initialization function nrf_modem_lib_init() terminates with an error.
The error log is as follows:...
While working on a device for personal use, I needed to reference some official BLE documentation. I noticed that many of the documents — including:
[BLE Core Specification...
I upgraded from v2.7.0 to v2.8.0 of the nRF Connect SDK and noticed that the UART was no longer working.
It seemed the UART receives one byte and calls exit. Transmit doesn...
Hi,
Apologies for a newbie question (I am far from a developer and just need to flash firmware)
I have a nRF52 DK connected to my PC running nRF Connect for desktop...
Hello everyone,
This might be a somewhat silly question. I'm trying to use SDK v17.1, and have an issue with the app_timer library.
I remember that before SDK v13 one...
