Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Basically, I cannot do continuous TX with nrf_libuarte_async:
Here is simple reproduce:
It only output ===TICK=== and no +++TOCK+++
Here is what I've tried:
...
Hi,
On the nRF52810, is there any limitation on using P0.12 with I2C? I am using MS50SFA module on a custom PCB.
I've also noticed the same issue on a nrf52 DK while using...
i use ncs1.5.0 and nrf5340dk_nrf5340_cpuapp, i disabled uart0 ,enabled uart3, disabled hci_rpmsg out ,and connect uart3 rx pin p0.32 ,tx pin p0.33 to a 232-usb connecting...
hi
I use nrf52 sdk17. i want to change device name .
1. if device name is less 19, more 18 ,it is ok. for example
#define DEVICE_NAME "123456789123456789" . it is OK...
Hi,
I'm trying to catch my NRF packets with nRF Sniffer for Bluetooth and I can't find them (after starting advertising).
On the other hand - I'm able to connect to the...
Hello,
I am stuck on the step of getting the Thingy91 to start working.
I am following this tutorial: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
i am working on nrf52dk. i have already implemented dfu with button. i want to implement buttonless dfu. as there is a example provided in ble_peripheral with name ...
I'm more of a programmer than an electronics person so I apologise in advance if I misuse terminology or if the answer to this would be obvious if I had more experience. ...
Hello.
I want to raise the SDK version, what should I do at that time? (Example: v16.0.0 → v17.0.2) Should I overwrite all the old SDK sources I'm using with the new SDK...
Hi, I'm using the PWR_MGMT SDK 17.0.2 demo code on my nRF52 DK.
Q1) After enabling parameters in the sdk_config.h, the nRF52 DK could enter the Power Off Mode if I press...
I am trying to conduct a device firmware update using nrfutil's dfu ble functionality. Here is the command:
However, running the above command results in the following...
Has anyone used SDCard interface with either 52840 or 5340 in anything other than SPI mode? I just noticed in the SDK 15.3 code we are using SDCard is in SPI mode. Seems max...
Hello,
I want to connect an external led to the nrf5340 pdk to perform the same function as the blinky example.
I connected this led to D0 (PIN P1.00), but I don't know...
