Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
Hi,
I am new to nRF Connect SDK. I am trying to achieve over the air Firmware upgrade through nRF5340. The SDK i am using is nRF Connect SDK v1.5.0 .
As per my understanding...
I am currently going through the usbd_ble_uart example and understanding what states make which LED's active,
Within the example, LED_BLE_NUS_CONN is defined as BSP_BOARD_LED_0...
How to use the internal 32.768k crystal oscillator for nrf5340？
NCS: V1.5.0
example: ncs1.5.0\v1.5.0\nrf\samples\peripheral\radio_test
Only HF no LF config.
Hi all,
I'm trying to use one of the built in sha256 libraries. As I've enabled the CONFIG_NRF_CC3XX_PLATFORM and CONFIG_NORDIC_SECURITY_BACKEND I thought I would pick this...
I am working on a BLE Product which connects to a remote device when detected within a certain proximity (based on the RSSI values). After switching on the scanning, I receive...
Hii Guys,
I am trying to run example code ble_app_uart on my nrf52810 sdk module . But when I try to run the code in debug mode I get an error of Vector Catch Error ....
Hi, I am working on nRF52840. I want to add GSM MQTT protocol. Is there nordic soc available for this? Which we can later communicate with nRF52840 peripheral device also...
Hi Everyone,
I am working on nrf52832, I am using sdk15.0.0 ble_beacon_app.
I want set tx_power but when softdevice enable gettting error.
I am tried using sd_ble_gap_tx_power_set...
Hi.
When I click add new LTE Device, I get the same menu as when clicking add new SIM Card. When is click register with IMEI and PIN assosiated to my nrf9160DK, I get. ...
Hello All,
I am developing a light control device using Zigbee and Alexa. I am using an nRF52840 device and SDK nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71.
For my development...
Hello Everyone,
I am a beginner
I am working on a project which requires authentication of the firmware , for this purpose i want to generate the hash of the firmware...
Hello OT Team,
I am working on the custom product where Openthread would be used. I am facing the issue while commissioning the other device to join the network.
The...
Hi ,
I tried following steps to configure and toggle GPIO pins.
I have also set CONFIG_GPIO=y i n your prj.conf file. ,referring to https://devzone.nordicsemi.com/f...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi,
I have followed the documentation here trying to get the radio_test project working for FCC certification:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom...
