Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am keep trying to get the BME680 example to work with the nRF52840-DK using Zephyr.
I check and successfully find the node for the BME680, but "device_get_binding()" for...
Hi,
I am using
I am able to list BLE devices using the below example.
SDK = nRF5_SDK_15.3.0_59ac345,
Example : nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_gatts...
According to this thread, iPhone 11 Pro supports Long Range (Coded PHY) : https://devzone.nordicsemi.com/f/nordic-q-a/33060/is-there-any-smartphone-with-supporting-of-bluetooth...
Hello,
I am upgrading to SDK 17.0 from 15.0.
When I try to to compile my project i get this error:
../_Release/Release_Commercial_Debug/Main/Exe/Main.elf section ...
Hi,
I followed the tutorial in the Github and create a custom service. (Github: https://github.com/NordicPlayground/nRF52-Bluetooth-Course )
1. I use the ble_cus_custom_value_update...
I have an issue with my Thingy:91
1) I unboxed
2) I successfully connected to my Windows machine and updated the modem firmware
3) Turned off power
4) Turned on power...
I would like to add a simple ble BAS (battery service) to appear along side my custom services... but for the life of me I cannot find any information, or tutorial on how...
I build project without problems, but this simple sample return zero results for read buffer. I return 5 zero from 5 zeros. I have right names for overlays files. nrf9160_pca10090ns...
I'd previously run into this problem with mqtt_publish not being able to handle large payloads, larger than approximately 2k.
At the time, the suggested workaround was to...
Hi All,
I am working on a project where i need to communicate using i2c protocol. For this i need to set i2c frequency 20 Khz. So how can i calculate register value to set...
software : nRF5_SDK_14.0.0_3bcc1f7
hardware :nrf52832qfaa
example : ble_app_hrs_rscs_relay
i want use "example : ble_app_hrs_rscs_relay" to receive more then 20 byte...
Hi all,
I have a DK 10056 rev 1.0.0, and it suddenly stopped working on the Embed side. Using the USB port (the DK one, not the NRF one), the LEDs (4 LEDs for testing purposes...
Hi,
I am using an nRF52 based chipset and programming the device with the hex file.This is being performed using the nRFConnect v.3.4.1 Programmer. The erase and write option...
Hi,
I have a custom prototype board based on nRF52833 which runs a working firmware and I have not any other prototype ready to hand.
Unfortunately, I think that the source...
Hello,
Considering the waveforms in the following chart, which will be the best approach to keep the power consumption as low as possible?
Specifically, which peripheral...
