Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I'm working on adding support for a custom NRF9160-based board to the ncs project. It appears to be working by simply duplicating the DK and making some modifications, however...
Hi,
I merge saadc and ble_uart together in order to send send sensor output(now just analog voltage) to mobile app. I want to check weather the ADC is working properly or...
Greetings to all,
I'm using nRF52840 with the latests SDKs (nRF5 SDK 15.3.0, mesh SDK 3.2.0). I have two questions which are related-
I'm trying to find a clever way...
I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I am looking for (andriod) mobile phone that support Bluetooth LE coded (long range)
Have you ever tested bluetooth (LE coded) with mobile phone ?
Please recommend...
I am currently developing firmware that needs to run on both 32 and 40 chips.
The basics of the situation is the firmware contains 3 'applications'. A flag in the UICR region...
Hello,
I have been looking through the SDK for the Thingy:52, and I have been unable to find the configuration file used for the MPU-9250. I am able to see the default pedometer...
I use QSPI to access MT25qu512 serial flash and find the following behavior.
SDK: nRF5_SDK_15.3.0_59ac345
QSPI configuration:
// Use 4 bytes address from serial flash...
I am unable to figure out what causes the problem that IRQ handler is defined both in nrfx_uart and nrfx_uarte modules.
After investigating in a test project I have found...
I have previously built the Asset Tracker downloaded it to my 9160DK with no problems.
Today I connected my Thingy91 and updated it's firmware. Afterwards I built the Asset...
Hello,
I'm trying to create a Mesh network with the following devices:
* Mobile phone as provisioner (supports PB-GATT only)
* Two different bulb's which supports PB...
When storing entries that aren't multiple of 4 bytes they are padded with random bytes by flash manager.
The problem is that they aren't padded with 1's but rather random...
I'm testing with a Custom board using a nrf52832 chip.
Testing BLE communication using nRF Tool Box.
I am using SDK15.3.0 example for communication using nRF Toolbox and...
Hi,
I am trying to install the nrf command line tools on linux. After following the installation instruction, I have the error
ERROR: nrfjprog.ini not found. Please reinstall...
