Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
As noted in other discussions, like the one I've linked below, there is no timing information for the QSPI interface. Can Nordic please provide the timing information for...
Hi! I'm able to update the firmware on the nrf5340 over BLE but the BLE settings seem to get overwritten during the update. The master device cannot automatically reconnect...
Hi, im working in a project with the nRF5340-QKAA and I need VDD as output 1.8V, for this reasoin I supply the uC with 3.6V on VDDH like this image:
this works fine...
I'm working on developing a desktop app, which can communicate with nrf52840-dongle or any Nordic device. I'm using UWP to develop the app. I'm new to App development so i...
Hi,
I'm evaluating the nRF9160-DK with the SOFTSIM feature enabled.
I would like to know if there is a way to tell the softsim to wait for APDU response for more than...
Hi, I have a BLE application where I want to use the device firmware updates (DFU) over Bluetooth. I followed the nRF Connect SDK Intermediate tutorial on how to enable the...
Hello!
I'm using the nRF5340 for a school design project and as such am financially limited to relatively low cost board manufacturers.
It seems that most of these manufacturers...
Greetings,
I'm trying to add an existing folder from a project with its' contents, but it seems that it only adds files that are included in the folders, the other nested...
Hello,
I am currently working with the Nordic nRF9160DK and am using the https_client example from the examples in the nRF Connect via VS Code (on Windows OS), and as far...
Hi,
I have been trying for months now and don't seem to find a way to build a signed app for mcuboot without having to build the whole mcuboot itself.
In the board files...
hi,
I am using nrf9160+NCS v2.6.1. When the CONFIG_SHELL_BACKEND_RTT feature is enabled, the power consumption increases by 80uA. After investigation, I found that the default...
Hi
Built and flashed ncs2.7.0 SLM application at NRF9151 DK. It will log booting log messages and then "Ready" as below.
Before ncs2.7.0, I found SLM application only...
Dear All.
Using, for instance, a peripheral nRF52840 SoC, would it be possible to change in real-time the text string being advertised, among several prerecorded ones, according...
Hi,
I am following the tutorial to implement the serial recovery on nrf52840DK https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders...
