Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
I have code working for interfacing the nRF52 DK board to a SSD1309 based 2.42” OLED display.
The problem is with getting the correct indexing for lines and columns.
Can...
Hello,
we are experiencing rejection from the network by receiving cereg notification. Modem afterwards stops attempting to connect to network. Which results in application...
I had used nRF52840 DK sometime ago and successfully tested it with different codes. But now when I connect the kit to the PC, it is not getting detected by the same PC that...
We just ran into an issue with multiple build names for nRF Connect's plugin for VSCode on Mac.
Start with "Launch build_a", "Launch build_a_v1", and "Launch build_a_v2...
Hi, here comes a few VSCode plugin bugs, it's really the first one that is the main one, but thought I might as well "dump" the rest of the quirks and bugs I have with it...
Hello,
I am unable to see my Nordic Thingy 53 using the nRF connect desktop app, I can use the apps on my phone, but I need to be able to use my computer for a class....
Hi Nordic Teams:
I'm using Nordic Connect SDK v3.1.0 and nRF52840, I want to update USB iSerialNumber string in hid-keyboard samples.
I tried two methods but they didn...
Hi,
I'm not able to flash nRF54 DK. Log as below:
2025-08-29T06:47:39.828Z INFO Initialising the bundled nrfutil device 2025-08-29T06:47:39.874Z DEBUG Started watching...
*Note that this is only an issue when the central and peripheral are simultaneously active.
This is my current setup for starting advertising, but it requires a deprecated...
Intro We are using the nRF9160 with sensors we manufacture. The code developed is based on the serial SLM sample, toolchain v1.6.0. I am trying to keep the code/project files...
Hello. I have an issue with my development board. When attempting to recover the board, i cannot due to access port protection. This is the specific error message from the...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
am trying to mount little fs example with my external flash winbond w25q256 but my nrf52840 board taking internal memory and am using qspi
it get automount and writing in...
Hi Nordic,
I need to build an Auracast broadcast speaker (LE Audio BIS broadcaster). Besides audio, I also need two-way data exchange between the Auracast source and the...
Hello,
I am trying to have my own BLE advertising and scanning (with filtering) custom service (from now on peer service) in parallel with BLE mesh. So far I've been able...
