I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hey Team, I was playing around with the composite example, and added in my own class a and used the mouse class to implement it while changing it to suit what i have orgianlly...
I'm working on a custom board with a nRF52840 and a Micron NOR Flash MT25QU128ABA8E12-0SIT ( https://www.micron.com/products/nor-flash/serial-nor-flash/part-catalog/mt25qu128aba8e12...
Hello,
I use BroadVoice32OpenSource.v1.2.zip to test encoding and decoding,On windows10 or 52840，
using 16bit 16Khz Continuous audio，And has been converted bin2c array...
Hello All,
I am developing an nRF52840 MCU base thread product.
For this I am using nRF52840-Dev_kit for Development and SDK - nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b...
Hello!
We have a new board design we are working on that uses the new nRF5340 chip, revision Engineering A.
However, we are having difficulty getting the SPIM4 (High-Speed...
Hi All,
I'm a little rusty on my embedded C and was wondering if I could get a few broad pointers on the best way to organize this research system I'm putting together...
Dear Nordic:
I have a STM32 family MCU with a preloaded bootloader, to which I can update the firmware via UART. The goal I want to achieve is the following:
I want to...
Dear all,
We are using nrf52832 as our main MCU. In our development we need two uart. Among them first is Hardware uart which is working perfectly and second is software...
I am using the Arduino Nano 33 BLE Sense (with nRF52840) which comes with a mounted MEMS PDM microphone ( MP34DT05 ). My project will be battery powered and thus calls for...
I have successfully implemented the Azure IoT Hub sample on my nRF9160DK and added the ble scanning module. The kit is acting as a gateway, reading advertisements from a couple...
Hi ,
Device :- nrf52840
USB class :- CDC ACM
We are sending the ADC data (240 bytes at a time) to Host computer over USB (Full speed) and checking the received data...
Hi,
Using the Nordic secure bootloader for dfu OTA update, I am facing an issue causing the system to go under a condition where the bootloader is not any longer able to...
Hi. I'm trying to output frequency ( in the 1,250 Hz to 1,750 Hz range ) on GPIO. Each frequency should be outputted for 5ms time. For that, I use 2 TIMERs: one for 5ms counter...
Hi, we use nRF9160 and SDK 1.7.
in one of our applications, we need more than actually available flash. Now we have ~420kB for application - because we use MCUBoot and dual...
As title says, I cannot get anything to change in autoconf.h after changing the corresponding value in prj.conf using nRF Connect samples. I have tried both Project-->Reload...
