I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
Currently I want to build the light_switch examples from the nrf5_SDK_for_Mesh_v2.2.0 on my nrf52832 dev board but this gives the following error "boards.h: No such file or...
I would like to know if Nordic has implemented software support for CryptoCell-312 (nRF5340) in the latest master branch?
Right now I am able to use mbedTLS "frontend",...
Hello All
Please tell me about nRF Connect (iOS).
When the module and nRF Connect (Ver 2.0.1) are connected using LESC, they will be disconnected after bonding is completed...
I am using the ble_app_uart example and I am having a hard time finding the function that writes a UART message to BLE from the Nordic to the host. uart_event_handle() seems...
Hello All,
I am working on nRF51822 use SDK nRF5 12.3.0 version in IAR workbench.
I am write data in the flash so for that i follow below steps,
Step 1: press button...
So, I need to send and receive a data frame with 39 Bytes with a system Dongle-Arduino(with a nRF24L01 module).
My problem is, I tried to configure Dongle to communicate...
Hi,
I cannot update the firmware on the nrf9160 MLM1 Preview development kit we have. Is this possible? or is the devkit voided for the latest nrf connect and nrfjprog...
Good afternoon everyone,
I'm trying to make a working application for the BLE NUS example but with the support of FreeRTOS that is MANDATORY. I work with KEIL. I started...
with NCS v1.3.0 is there a way to turn off partition manager? I want to be able to build my app and mcuboot separately and not use partition manager at all.
Is it possibe to upgrade nRF52-DK on board programmer to program nRF52840? I already have this nRF52DK but in final I found that 52840 will be better choise for my proyect...
Hi, I am reading the datasheet of both the sensor. but i2c register are different.
I am currently work on vl53l1x. please give me the response as early as possible. thanks...
Using SDK 16.0.0 on an nRF 52840 board.
Managed to get a board into a state where it had only data pages and no swap pages, and therefore fds_init fails with the NO_SWAP...
I want to use nrf SPI driver for SPI flash implementation. For that want to send either SPI transmit or SPI receive at single instance to write or read flash address. But...
Version: Mac OS X 10.15.5 (19F101)
I'm using the nRF Connect app Getting Started Assistant and manage to get through most of it. However, when I use Segger to open up a...
Im trying to run http_client example in zephyr folder (ncs\v1.3.0\zephyr\samples\net\sockets\http_client). When i debug, the app run to fault, i dont know what fault but it...
