How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Currently, I am using the ble_app_cts_c example and I want to disconnect the connected device.
I want to know how can I check the condition for any connected device?
and...
Hi.
i am using NRF52832 DK with MESH SDK
can i transmit string from Low Power Node to Friendship node.?
If yes kindly let me know what changes i need to do for that...
I have observed two issues with using the UART in an ncs project and I'm not sure exactly where the issue lies (Nordic or Zephyr).
Firstly, and most importantly, according...
hello Nordic
i am using nrf52840, sdk 16.0 working on ther peripheral ble_blinky example, working with Segger IDE (ses)
i have lines of code missing when i am debugging...
HI,
I am trying to connect multilink central to multiple peripherals. I am able to connect using "target name". But i dont know how to connect using central to peripheral...
HI,
Currently, I am using the ble_app_cts_c example and I am able to pair only one device. I found out that it is related to whitelisting function.
How can I disable the...
On SDK16.0.0 + Mesh SDK 4.1.0
I've followed this to add PA/LNA support in the bootloader (Fanstel BT840X). I see the increase in RSSI and know that it is working.
...
Hi,
I am evaluating the Light Ctrl example of the Connect SDK 1.4.2. After nRF52840DK was programmed and provisioned by iPad, Mesh App, I was trying to bind application...
Hi,
I have built the example hrs_uart project and it works fine when I load the image into a pair of OCA10040 demo boards, one as application board and the other as connectivity...
Hi,
I am currently testing QSPI communication for flash. I am using the Termite console. When the console starting I got this error message:
uart:~$ [1B][8D[1B][J[00:00...
Hi,
I am trying to create a Mesh Network using CCT controlled lights and switch.
I want to fetch the present lightness value of the light(server) from the switch(client...
Hello,
I'm currently using SES for SW-development (NRF52). But especially for legacy code and refactoring I think this tool is absolutly not suitable (basic functions like...
Hi
We are using this combination of software:
Mesh SDK 4.2
Bluetooth SDK 17.0.1
Softdevice 7.0.1
Mesh DFU using the precompiled bootloader binary mesh_bootloader_gccarmemb_nrf52840_xxAA...
Dear sir,
Our code gets compiled using command emBuild.exe For programming NRF Connect Programmer tool is used.
I get following error while hex file is added to programmer...
HI All !
Hope you all are doing well !
I have a question regarding "Exporting Segger Embedded IDE Project/SDK to Arduino IDE or Vscode Studio" The Reason i want this is...
