In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hello,
when I send notifications or indications to central device without bonding it works perfect. But after bonding they are not sent. I receive following logs when cetnral...
I am using nRF52840 dongle and nRF SDK version nRF5_SDK_17.0.0_9d13099.
When I am trying to debug the application it gives an error.
using your example project on nRF52840...
I can't go into too many details, but the scenario we have is:
We have an NRF52840 device connected to a PC through serial (for both power and communication) The NRF device...
I am trying to create a minimum working Keil uVision 5 S132 project with PCA100400. When I compare the examples with mine, I notice that during startup, when the code of flashed...
Hi
I heard in the "nRF Connect SDK" presentation from May 2020, that the nrfSDK only support BT 5.0.
Is this still correct that the features of BT5.1 and BT5.2 are not...
Hello,
I want to use RAM to keep some data after a soft reset, so that I can find problems after reset. And I also found some implementation methods, such as using .non_init...
Hi so I ran this example:
https://devzone.nordicsemi.com/f/nordic-q-a/40476/unable-to-convert-to-long-range-after-looking-at-umpteen-examples--/157426#157426
When I went...
I need BLE sniffer and I puchase this device because in this manual of "nRF Sniffer" say that "nRF52840 Development Kit (PCA10056) " is compatible.
https://infocenter...
Hi,
Looking at the footprint you supply for the aQFN73 package (I have looked at the one supplied for nRF52840), I see that the pad have a size = 0.275mm. If IPC-7351 is...
Hello,
We have a product that sends out an ESB message approximately ever second, it does this using the RTC timer with the following setting:
It sends the message...
We want to add the nRF52805 to an existing product but also want to have the option to perform a firmware update.
The current DFU implementation doesn't allow the softdevice...
Dear friend Through github: github.com/.../v6.0.1 downloaded nrfutil.exe windows executable file, it can run perfectly on windows 64 bit. However, it will prompt incompatibility...
Hi, all,
I am working on nRF52832 using pc-ble-driver-py bindings to interface my BLE peripheral. Now I want to build the BLE communication between one central to multi...
Hi
AFter setting the switch sw5 to nRF91, itried to update the firmware using nRF connect V3.4.2
I got the following Error
Error while probing devices: Error occured...
