I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
Hi there,
I recently upgraded to nRF Connect for Desktop v3.3.3 and the programmer module to v1.4.2 and I am experiencing the following issues. At first, when I would try...
Hi,
Iam working on a nrf52840 and trying to achieve data flow from BLE device using NUS and transfer this data through UART.Uart is configured as (TX:P1.01,RX:P1.02).Iam...
I am using an nRF52 dev kit. I have loaded the pca_app_hts_pca10040_s132 example into the board. I only added these lines of code
nrf_gpio_cfg_output(ARDUINO_9_PIN); nrf_gpio_cfg_output...
Hi,
There are several new drivers under "nRF5_SDK_15.0.0_a53641a\components\drivers_ext\", but no example now.
I have setup the HTS221 driver and it works. I turn to...
I'm using nRF52-DK, and following the quidelines from devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader . I'm using the prebuild "blinky_pca10040...
Im trying to interface nRF52DK to Custome build acceleration sensor.
I want to use I2C communication. Are the pin connections mentioned below sufficient?
...
The buttonless_dfu_sdh_state_observer in this example is shutting down the cpu when the softdevice is disabled using an observer.
I'm not sure why this is necessary...
Hi everyone,
I have a project written in C++ for nRF52 series using the SDK 15.3.
If I use Keil and uVIsion, the project compiles and works great. With the same source...
I am using nRF52832, And SDK 15.3, the ble_app_blinky project,
a. if i have installed only the latest version of Device family 8.29.0 , when i try to build the project,...
Setup and goal: I'm developing an BLE central app and would like to use scan address filtering to find a specific device. I enabled the filter and provided a hard-coded BD...
Hello,
I successfully downloaded SAADC SDK example in the peripheral folder. The hardware setup is as below ,
The pin configuration for this is as below
...
I tried implementing
https://github.com/andenore/NordicSnippets/blob/master/examples/temp/main.c
But i get 2.6V without connecting any of the Analog pins.
Exactly...
I have attached an Arduino INO file that I wrote early on in a project. It runs a probe. It is an amazingly simple probe but especially important. I am making a simple opacity...
Hi Team,
I planning to use vibration motor with nrf52832.
vibration motor will give maximum buzz on 20.3KHz(50 duty cycle).
So my question is
- Can I achieve 20...
