I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
My environment: Keil 5; nRF52832 SDK 15.2 ; Softdevice S132 6.1.0
The uart bootloader code locate in the address: 0x70000 - 0x80000 ; (The MBR in 0x70000)
The application...
Hi,
I want to read and write MAX30100's registers. How can i do that? I tried a lot of solutions but I didn't solve that.
For example; MAX30100's address is 0x57. And...
Greetings!
I am using the SDK Mesh 3.1.0 and Softdevice 6.1.0 with the nRF52840 Dev kit: (PCA10056)
So, in my previous post ( https://devzone.nordicsemi.com/f/nordic...
I am using the nRF 15.2 SDK for Thread and Zigbee. I am currently trying to use the debugger in SES, but when I upload the code, SES complains that it can't find the source...
Hi
my devices use USB HID to PC now, and I have PC GUI.
I want use BLE send My device data to PC ( windows 10 )
if I use BLE HID services to PC
I need to do any...
Hi;
I am trying to add uart central to multilink central examble. I added some of uart part to multilink. i am trying to link two peripheral to central. when two peripheral...
Hello Nordic, for my project work i am using nrf52840 dk. with segger embeded studio i drag and drop the s140 softdevice hex file into the J-Link (chip PCA10056). and i tried...
Hello,
we are using the Nordic nRF52832, and I was hoping to update to the new SoftDevice S113 v7.0.0 as it seems like a better fit for our use cases than S132.
However...
My flash_placement.xml file is here and I am getting this error `.bootloaderSettings' will not fit in region `UNPLACED_SECTIONS'.`UNPLACED_SECTIONS' overflowed by 1024 bytes...
Hi
I have done multilink with uart and getting data from multiple ble_uart peripheral. now i have to read data from only one peripheral . what will do for that.
I am using...
Hello
I was wondering if there have been any changes in supporting IAR for nRF Mesh?
In your answer from about a year ago you wrote that you were not currently planning...
Hi,
I have some questions:
1. How does the process of getting addresses to the Nodes happen in Mesh stack? Is it automatically or I need to set it when I flashed the...
Trying to run the "Alert Notification Application" example in nRF SDK v15.3.0 on either a Windows 10 system or a Ubuntu 18.04 LTS system. Following the instructions, I can...
hi,
i want to use mesh network in my project.our requirement is multiple nodes will be sending data to one master node.is there any example code.
Regards,
jagadee...
Hi,
We have a gateway device that contains the nRF51822 MDBT40 Raytac module.
We are designing a new nRF52832 based sensor and we want to connect 20 of them to the Gateway...
