How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hello, I am trying to flash the nRF52840 SoC on the nRF52840 DK using an external J-Link debugger, without relying on the interface MCU or the onboard J-Link. My current switch...
Dear Nordic Engineers
I used NCS2.9.0 to develop a device based on nRF52840 and I would like to use UART to DFU the device based on SMP.
Now, I test SMP samples and use...
Hi,
After the latest update, the below setting allowing me to select nrfjprog as my device provider is now gone:
I am using the nRF Playground Docker container...
Hi,
I have been using NUS code to stream data between mobile and nrf5340 audio dk. is it possible to stream 256KB of data at a go? what is the maximum MTU size that i can...
I am using nrf connect sdk 2.7.0 with nrf52811.
My application is based on nrf5-sdk V 17.1.0 but now i want to port it to nrf-conneck sdk 2.7.0.
I want to know whether...
I have a problem with the package with nrf5 sdk, there for pca10100 examples are not there. i am trying to interface quadrature decoder with one encoder and it is not able...
Hello,I have a custom board using a Nordic nrf52823 microcontroller on it. I am using VSCode with the nrf connect SDK and the Zpehry RTOS- I want to make use Zephyr RTC to...
Is there any relevant assessment or introduction document of IC FMEA?
For example, the impact of abnormal short circuit and ordinary short circuit on chip 52832;
And...
1、I used the spi_bitbang routine to port it to the network core to run, and after the program was burned, I used an oscilloscope to measure the CLK pin waveform and there...
Hi,i I am testing the sample(ncs\v2.7.0\zephyr\samples\drivers\spi_bitbang) at a 52840DK board, with overlay setup like these:
spibb0: spibb0 {
compatible = "zephyr...
Hi nRF support team,
I am trying to add a new Custom Service and Characteristic an application on nRF82540 development kit using the nRF Connect SDK.
Can you please let...
Hello.
1. The nPM1300 PS v1.1 states in Section 6.1.1 the fllowing: "The default current limit is IBUS100MA (100 mA)". But the values after reset in registers VBUSINILIMSTARTUP...
I have finally got FOTA working with external flash, but I have a strange problem.
When the FOTA is complete, the mcuboot fails, but the new image boots correctly.
So...
Hi, I am trying to change the USB CDC/ACM com port name. I have read through some posts but they are very short or unanswered. It seems we can change the .inf driver file...
